Push Blocks
Moderators: HopefulSSer, admin
Push Blocks
The bottom of a couple of my old Shopsmith push blocks are deteriorating. Has anyone redone them? If so, what did you use?
This one is not terrible This one is toast...
This one is not terrible This one is toast...
- dusty
- Platinum Member
- Posts: 21368
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Push Blocks
I cut some mouse pads to size, cleaned the old pads off the push blocks and reattached to mouse pads to the push blocks.
Apply the adhesive to both the push block and the mouse pad. I don't recall what adhesive I used.
Apply the adhesive to both the push block and the mouse pad. I don't recall what adhesive I used.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Push Blocks
Remember that you may have to replace them in the future. Be careful which adhesive you use, since you may have to clean it off again.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
Re: Push Blocks
Mouse Pads, who would have thought, but they actually sound perfect. I was thinking 3M super 77 or super 90 adhesive
- dusty
- Platinum Member
- Posts: 21368
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Push Blocks
Nice job for the belt sander
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Push Blocks
As an update, the mouse pad material seems to be the trick. I found these desktop mouse pads at Wal-Mart. Cleaned the old stuff off and scuffed the block with 180 grit and used spray adhesive to attach the new material and trimmed it with a razor knife.
Came out great
Came out great
Re: Push Blocks
Tom from Woodshop Nerdery posted a video on YouTube where he used tool box drawer liner as a pad replacement.
In addition to replacing the pads he added a “ heel” to one of his pushblocks.
https://www.youtube.com/watch?v=AceTAfItf48
In addition to replacing the pads he added a “ heel” to one of his pushblocks.
https://www.youtube.com/watch?v=AceTAfItf48
Re: Push Blocks
That is a cool idea, just got a little project for today, thanks.benmcn wrote: ↑Sat Jul 30, 2022 11:10 pm Tom from Woodshop Nerdery posted a video on YouTube where he used tool box drawer liner as a pad replacement.
In addition to replacing the pads he added a “ heel” to one of his pushblocks.
https://www.youtube.com/watch?v=AceTAfItf48
Re: Push Blocks
If the mouse pads aren't grippy enough, Lee valley sells high friction sheets.
https://www.leevalley.com/en-ca/shop/to ... ion-sheets
https://www.leevalley.com/en-ca/shop/to ... ion-sheets
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,