Mark VII a start and a long ways to go..
Moderators: HopefulSSer, admin
Re: Mark VII a start and a long ways to go..
I really like it with the butcher block. Very nice!
Mike -
Mike -
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
Re: Mark VII a start and a long ways to go..
Thank you Mike, I need to something about the ugly red plastic….
I may be old but I’m slow
https://www.schmuckatellico.com/
https://scshiftknob.com
https://www.schmuckatellico.com/
https://scshiftknob.com
Re: Mark VII a start and a long ways to go..
Just let me know which ones you need. Not sure if they are threaded or molded on? If threaded, I can make them.
Mike -
Mike -
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
Re: Mark VII a start and a long ways to go..
Thank you Mike, I may take you up on that offer. One is threaded for sure the others probably molded.
I may be old but I’m slow
https://www.schmuckatellico.com/
https://scshiftknob.com
https://www.schmuckatellico.com/
https://scshiftknob.com
- JPG
- Platinum Member
- Posts: 34643
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark VII a start and a long ways to go..
Threaded???
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Mark VII a start and a long ways to go..
The plastic quill handle end and the crank handles are a press fit onto the end of splined rods. Not threaded. Not sure about the little table interlock thingy.
Mike
Mike
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
Re: Mark VII a start and a long ways to go..
Yes the interlock thingy is threaded.
I may be old but I’m slow
https://www.schmuckatellico.com/
https://scshiftknob.com
https://www.schmuckatellico.com/
https://scshiftknob.com
Re: Mark VII a start and a long ways to go..
Getting close, was hoping to be finished…ran it and she runs beautifully. 800 RPM low end and 6000 or so high end and the dial clicks very smoothly. I was very happy, much nicer than my other machines. I have attempted to install upper and lower guard and was wondering about the following, knowing the parts I’m using are not necessarily for this model.
1. There is a slot about 3/4” wide on each side that would appear to let sawdust fly out of lower guard. Any idea what these slots are for?
2. The lower guard front plate just barely rubs on the blade. I read requirement is at least a 1/4” clearance. Do I have something installed wrong or is there a shorter arbor?
3. It appears there is still a lot of blade exposed and not a real good seal for dust. Is this just the way it is?
Many thanks for any assistance or clarification.
1. There is a slot about 3/4” wide on each side that would appear to let sawdust fly out of lower guard. Any idea what these slots are for?
2. The lower guard front plate just barely rubs on the blade. I read requirement is at least a 1/4” clearance. Do I have something installed wrong or is there a shorter arbor?
3. It appears there is still a lot of blade exposed and not a real good seal for dust. Is this just the way it is?
Many thanks for any assistance or clarification.
- Attachments
-
- IMG_2608.jpeg (428.36 KiB) Viewed 1743 times
-
- IMG_2609.jpeg (356.05 KiB) Viewed 1743 times
I may be old but I’m slow
https://www.schmuckatellico.com/
https://scshiftknob.com
https://www.schmuckatellico.com/
https://scshiftknob.com
- JPG
- Platinum Member
- Posts: 34643
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark VII a start and a long ways to go..
Is the quill shaft 1 1/8" proud of the collar? Looks sorta short????
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Mark VII a start and a long ways to go..
I think you can slide the guard out some on the quill?
Mike
Mike
ShopSmith Mark VII (406982), with Band Saw, Jig Saw, Belt Sander, and Jointer
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper
ShopSmith Mark VII (400457), (working backup or parts machine)
12" Craftsman Band Saw (113.243311)
12" Craftsman Powered Hacksaw (108.1501)
12" Atlas Commercial (3990) 12" Back Geared, Undermount, Screw Cutting Lathe with Quick Change Gear Box, Taper, Milling and Grinding Attachments
Atlas MFC Horizontal Milling Machine with Vertical Milling Attachment
Atlas 7B Metal Shaper