New to me belt sander and stand

Create a review for a woodworking tool that you are familiar with (Shopsmith brand or Non-Shopsmith) or just post your opinion on a specific tool. Head to head comparisons welcome too.

Moderators: HopefulSSer, admin

User avatar
chapmanruss
Platinum Member
Posts: 3449
Joined: Tue Aug 26, 2014 8:16 pm
Location: near Portland, Oregon

Re: New to me belt sander and stand

Post by chapmanruss »

The Jointer will work fine on the Power Stand. Just use the correct pulley combination to get the actual correct speed. Remember the speed setting used for it on the Mark V (and other Marks) is slower than the actual speed it is running at on the lower Idler's shaft than the speed is for the upper Drive Sleeve Assembly's shaft.
Russ

Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
larryhrockisland
Gold Member
Posts: 241
Joined: Sun Aug 19, 2007 10:47 pm

Re: New to me belt sander and stand

Post by larryhrockisland »

I ordered a new drive sleeve for the belt sander and it came in the mail today. The original sleeve was missing so I don’t know what it should look like but the replacement appears to be a piece of bicycle inner tube. Does it need adhesive?
7C993BDD-7A3E-4DB8-B235-F0D1C1382553.jpeg
7C993BDD-7A3E-4DB8-B235-F0D1C1382553.jpeg (363.51 KiB) Viewed 702 times
Larry Hargrove
Rock Island, Ok
1981 Mark V 500>510>520(98922)
19?? Mark V 500>Power Pro headstock 556176 06-17-11 factory exchange program original serial unknown
1957 Mark V 500 (350389)
1953 10ER
Another 10ER
Bandsaw 2012 Jointer 2012
Bandsaw, Jointer, other goodies
Craftsman table saw, Delta 46-460 Midi lathe
SS 6” Belt Sander w/power stand 1970’s?
User avatar
rpd
Platinum Member
Posts: 3039
Joined: Tue Apr 05, 2011 3:22 am
Location: Victoria, B.C.

Re: New to me belt sander and stand

Post by rpd »

Can't find the reference posts, but if I recall correctly people have recommended. Blow compressed air under the edge of the sleeve while pulling onto the drum. Roll one side back over the other, apply glue and roll back, repeat on the other side.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
larryhrockisland
Gold Member
Posts: 241
Joined: Sun Aug 19, 2007 10:47 pm

Re: New to me belt sander and stand

Post by larryhrockisland »

Thanks
Larry Hargrove
Rock Island, Ok
1981 Mark V 500>510>520(98922)
19?? Mark V 500>Power Pro headstock 556176 06-17-11 factory exchange program original serial unknown
1957 Mark V 500 (350389)
1953 10ER
Another 10ER
Bandsaw 2012 Jointer 2012
Bandsaw, Jointer, other goodies
Craftsman table saw, Delta 46-460 Midi lathe
SS 6” Belt Sander w/power stand 1970’s?
Post Reply