Page 1 of 3
Power Coupler Strip-Out
Posted: Thu Aug 13, 2009 7:54 pm
by randythewoodchuck
I have stripped out the "threads" of 2 power couplers, at the end that connects to the headstock, in the last 6 months or so. I've a 500. I've owned it for a couple of years but really only used it for the last year or so. Is this to be expected or am I doing something wrong?
-Randy
Posted: Thu Aug 13, 2009 7:59 pm
by mbcabinetmaker
What SPT are you using? It could have a bad bearing or some problem causing the coupler to strip.
Posted: Thu Aug 13, 2009 8:06 pm
by beeg
I'd say "something" is wrong with this picture. Are you talking about part# 503574? Or the spindle hub?
Power Coupler Strip-Out
Posted: Thu Aug 13, 2009 8:33 pm
by dusty
FWIW, I just discarded one of my original power couplers. That would make it about 15 years old. Based on that, I would say you either have something wrong or maybe something is getting on the plastic in the coupler that has made it brittle.
Just guessing.
I'll be watching this for the feedback that will come from it.
Hope you have a replacement so that you can continue to make saw dust.
Power Coupler Strip-Out
Posted: Thu Aug 13, 2009 8:51 pm
by billmayo
randythewoodchuck wrote:I have stripped out the "threads" of 2 power couplers, at the end that connects to the headstock, in the last 6 months or so. I've a 500. I've owned it for a couple of years but really only used it for the last year or so. Is this to be expected or am I doing something wrong?
-Randy
I find that the headstock hub and the SPT hub are not perfectly aligned when this happens. I move the headstock hub againest the SPT hub and adjust the SPT mount and/or tubes until all 3 axes (X, Y & Z) mate snugly.
When I was using the bandsaw to cut metal, I was forced to go to a LoveJoy Spider 5/8" ID coupler. I got mine from Grainger.
http://www.grainger.com
The rubber spider shown is the most expensive one, they make cheaper ones.
A complete coupler requires two bodies and one insert(spider). This coupler requires excellant alignment too.
Posted: Fri Aug 14, 2009 7:00 am
by thainglo
billmayo wrote:When I was using the bandsaw to cut metal, I was forced to go to a LoveJoy Spider 5/8" ID coupler. I got mine from Grainger.
http://www.grainger.com
The rubber spider shown is the most expensive one, they make cheaper ones.
A complete coupler requires two bodies and one insert(spider). This coupler requires excellant alignment too.
Bill - I'd sure like to know more about the coupling setup you use. Do you remember the part numbers and have any pictures of the setup? I've been having the exact same issue.
Thanks!
Matt
Posted: Fri Aug 14, 2009 8:36 am
by regnar
I have used the Lovejoy couplers as well. They work out nice but I often loose the spider. Cheapest price that I have found is at use-enco.com
I use the series L050 5/8 bore Hubs . Enco's Part# 990-4047
And I use the Buna-N Spider. Its a softer rubber meant for jars and soft starts.
Enco's Part #990-4042
You can see all the sizes on page 1034 of their catalog. Your looking at about 7.85 + S/H for a coupling.
Posted: Fri Aug 14, 2009 10:29 am
by gregf
Those couplers are interesting. I've not come across them before.
Good to know about, thanks!
Posted: Mon Sep 12, 2011 5:18 am
by paulmcohen
billmayo wrote:I find that the headstock hub and the SPT hub are not perfectly aligned when this happens. I move the headstock hub againest the SPT hub and adjust the SPT mount and/or tubes until all 3 axes (X, Y & Z) mate snugly.
When I was using the bandsaw to cut metal, I was forced to go to a LoveJoy Spider 5/8" ID coupler. I got mine from Grainger.
http://www.grainger.com
The rubber spider shown is the most expensive one, they make cheaper ones.
A complete coupler requires two bodies and one insert(spider). This coupler requires excellant alignment too.
I went to the grainer site and could not figure out how this coupler actually works or what I need to buy can you provide additional details?
Posted: Mon Sep 12, 2011 6:59 am
by michaeltoc
paulmcohen wrote:I went to the grainer site and could not figure out how this coupler actually works or what I need to buy can you provide additional details?
You need 2 coupler bodies and one spider:
4X177 - 5/8" bore (headstock and most SPT)
4X176 - 1/2" bore (for some SPT)
1X409 - Spider
Mount the coupler bodies on the shafts (replacing the drive hubs). Fit the spider in-between the "teeth" and slide the headstock to mate the two couplers.
Be sure to check the shaft diameter on the SPT's - some (like the jigsaw) are 1/2" diameter. Purchase additional coupler bodies to mount on each SPT you have, plus an additional one to mount on the lower drive hub.
I have wanting to try this for some time, but I have some concerns with the PowerPro. The PowerPro may require a "zero backlash" coupling.