Page 1 of 2
Looking for used jacob chuck and 2 or 4 jaw holding jaws
Posted: Wed Jan 12, 2011 10:32 pm
by KDC
I am looking for a good used jacob chuck and also a 2 or 4 jaw lathe chuck for my 1976 SS. I looked on fleabay and they seem a bit pricey.
thanks all!
Posted: Wed Jan 12, 2011 11:45 pm
by JPG
kola wrote:I am looking for a good used jacob chuck and also a 2 or 4 jaw lathe chuck for my 1976 SS. I looked on fleabay and they seem a bit pricey.
thanks all!
Kola
Pricey? Compared to a 'new' one!
http://www.shopsmith.com/ownersite/itemfind.htm?item=505633&Submit=Find+Item
Posted: Thu Jan 13, 2011 2:37 pm
by ddvann79
Yeah, by the time you pay for shipping on most of those eBay chucks, you could have bought a new one from SS. I've tracked quite a few and even rusty ones go for $20 or more, plus shipping.
I don't see any way around it though. For me at least, when a chuck is broken or rusted over there's no making it right again. I need a chuck for my 1962 brownie (I've decided I like that better than "goldie") but I really don't like the prices I see out there, especially if you want the
Jacobsbrand!
Posted: Thu Jan 13, 2011 3:58 pm
by holsgo
The new Jacobs are not the same as the old ones. The old US made ones were sturdier but the chinese ones (which I just saw at Lowes) have a bit more plastic. Find an older US made one on ebay if you can.
Posted: Thu Jan 13, 2011 4:53 pm
by SDSSmith
The current Shopsmith drill chuck is a Shopsmith branded import jacobs-style chuck and is priced accordingly. The Jacobs 3326 and Jacobs Multi-Craft chucks come up on ebay all the time, are American made and can fit in a small flat rate box (~$5 shipping). If a person is patient, they should be able to get a true Jacobs chuck and key on the 'bay for under $30 delivered. Some of the earlier version Shopsmith Jacobs chuck had a chuck key that had a 5/32" hex cross piece. The chuck key could do double duty.
Posted: Thu Jan 13, 2011 5:02 pm
by JPG
1) The current ss chuck is not made by 'jacobs'. Just a fact, not a judgement!
2) Only source for chucks with a 5/8" bore is new from ss or used from??
3) There are two 'former' ss chucks out there, the later multi-craft MC8K26 and the older 3326. Some prefer the 3326, but I see little difference quality wise.
4) FWIW, they ARE repairable(new jaws,sleeves). Mickyd has restored a grossly rusted one.
Posted: Thu Jan 13, 2011 5:54 pm
by dusty
Posted: Thu Jan 13, 2011 6:11 pm
by SDSSmith
dusty wrote:Will
thiswork?
Not unless you bore out that 5/8-16 threaded area. Also, Shopsmith sold one other jacobs style chuck that was made in America...........hmmm trying to remember the brand, Cushman???? Yeah, that's it, some of the older Mark V/5's came with a Cushman chuck, also made in the good old USA.
Posted: Thu Jan 13, 2011 6:14 pm
by dusty
SDSSmith wrote:Not unless you bore out that 5/8-16 threaded area. Also, Shopsmith sold one other jacobs style chuck that was made in America...........hmmm trying to remember the brand, Cushman????
Thanks Rod. Obviously, I don't know how to translate the specs provided to real world. I was also looking at adaptors and now I think I under why I was confused there too.
Posted: Fri Jan 14, 2011 9:59 am
by KDC
Thanks for the advice all! I just bought a SS and I am thrilled. I will post pictures very soon. I got a 1976 SS with a bandsaw and other goodies for 200US bucks. It is in excellent condition and had one original owner. It did not come with a drill chuck and coupler.
The new one from shopsmith does not look bad and the price is right? Do these chucks have any runout issues?
I am still searching for a good used inexpensive 2 or 4 jaw lathe chuck. I found new 4 jaw chucks on fleabay for 150. the 2 jaw lathe chucks are hard to find. I'd like to spend 50-75 bucks..yeah I know I am a cheapskate.
