JPG40504 wrote:
That wide a span will be an issue(you will need a center load bearing beam) or very long very thick 'timbers' for joists.
I have a 24'x30' garage, and yes - you can make that span without a center beam. I have attic space above and the joists are 2x10, 12" OC (probably could have gone 16" if there was no storage space above).
Definitely go with 24x24 - for resale value alone, as it could be converted to a 2-car garage. 20x20 would be a little tight.
Michael
Mark V Model 500 (1985) upgraded to 520 (2009) and PowerPro (2011); Bandsaw, Jointer, Jigsaw, Planer.
michaeltoc wrote:Definitely go with 24x24 - for resale value alone, as it could be converted to a 2-car garage. 20x20 would be a little tight.
Not if you buy 2 Mini-Cooper's
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
cabotcat wrote:Good point on the 24 x 37 ' building. While i would love the space is must be in keeping with my neighborhood planning and th total cost to build.
That "cost" thing can get especially pesky.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
robinson46176 wrote:You can't get much closer to the Ohio than Madison IN.
Madison, IN - thats where my dad is from. Nice little town, and the hydro races are pretty neat. Then again, Madison is closer to kentucky than ohio...just cross the bridge
Mark 7, Pro Planer, Jointer, Bandsaw w/Kreg, Biscuit Joiner, Belt Sander, Jig Saw, Ringmaster, DC3300, Overarm Pin Router, Incra Ultimate setup
robinson46176 wrote:Not if you buy 2 Mini-Cooper's
.
I found that out recently...had a mini cooper and a mitsubishi lancer. sold the lancer and got an explorer - wow, big difference. Parking the explorer in the garage is a lot different than either of the small cars
Mark 7, Pro Planer, Jointer, Bandsaw w/Kreg, Biscuit Joiner, Belt Sander, Jig Saw, Ringmaster, DC3300, Overarm Pin Router, Incra Ultimate setup
dusty wrote:Don't over look possible code restrictions. I put in a 10'x20' shed for storage and could not go larger without a building permit.
My poor timing and lack of advance planning did not allow me to wait for a permit which can take FOREVER is you are waiting.
That is one nice thing about a gambrel roof. you can about double the space and especially if you do not put in any windows (until the dust settles) you can normally call it a one story building.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill