That is the same as my pix. The pix are looking from the 'left end'.]Yep, I mis-heard you!
10ER: Connecting Tubular Ways to Headrest?
Moderator: admin
[quote="JPG40504"]Howzit 'backwards'? That is the same as my pix. The pix are looking from the 'left end'.]
Yep, I mis-heard you!
That is the same as my pix. The pix are looking from the 'left end'.]Yep, I mis-heard you!
Heath
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
[quote="Eric"Shop"Smith"]Ok, things are starting to make sense. When I got it the upper screw in JPG's second picture, the one threaded into the tie bar with the allen wrench slot, was instead screwed into the head rest. It must have gotten switched around at some point. I was mistaken in identifying it as the the screw in the other thread. As is clear from JPG's picture, the proper screw has a much larger knob at the top. This would probably provide a more solid connection. I will have to look around in my box of little parts and see if I have it.
The screw that was mounted in the tie bar when I got it was a shorter version of the upper screw in JPG's second picture. It is about an inch long, its threads run its entire length and it lacks the slot for an allen wrench. I will have to try to figure out where that one is supposed to go.
I did have the tie bar on the proper side of the headrest and the instructions make it clear that is the way it is supposed to be mounted. I am not sure why the exploded diagram looks that way. It might be to keep the tubular ways from obstructing the view of the piece.
It is easy enought to determine where the large pieces go from photographs, but figuring out which screws go where can be a bit confusing when they are all made with the same diameter and thread. Thank you for all the help.[/quote]
I do not think that is a ss screw. A similar hex socket head screw secures the belt guard, but it only has 1/2" of thread.
The screw that was mounted in the tie bar when I got it was a shorter version of the upper screw in JPG's second picture. It is about an inch long, its threads run its entire length and it lacks the slot for an allen wrench. I will have to try to figure out where that one is supposed to go.
I did have the tie bar on the proper side of the headrest and the instructions make it clear that is the way it is supposed to be mounted. I am not sure why the exploded diagram looks that way. It might be to keep the tubular ways from obstructing the view of the piece.
It is easy enought to determine where the large pieces go from photographs, but figuring out which screws go where can be a bit confusing when they are all made with the same diameter and thread. Thank you for all the help.[/quote]
I do not think that is a ss screw. A similar hex socket head screw secures the belt guard, but it only has 1/2" of thread.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
Eric"Shop"Smith
- Silver Member
- Posts: 12
- Joined: Thu Oct 27, 2011 6:20 am
- Location: Gainesville, FL
That surprises me as the head is exactly the same as the tie bar screw, besides the lack of the hex socket. The same shape, the same dimensions, the same straight knurling. But I guess it doesn't make much difference; I will throw it in the box of small ShopSmith parts and forget about it unless I end up needing it.I do not think that is a ss screw. A similar hex socket head screw secures the belt guard, but it only has 1/2" of thread.