Rare Item!

JPG · Post by **JPG** » Sun Jan 15, 2012 3:50 pm

This ShopSmith item is so rare that they spelled the name differently!:rolleyes:

http://www.ebay.com/itm/Rare-Shopsmith- ... 20c1544395

It will fit a M10 though(and just about everything else out there)!:D

wiredone · Post by **wiredone** » Sun Jan 15, 2012 9:35 pm

yeah buddy, but this is my new favorite for the day.
http://www.ebay.com/itm/Shopsmith-10ER- ... 0136141389

JPG · Post by **JPG** » Sun Jan 15, 2012 9:50 pm

wiredone wrote:yeah buddy, but this is my new favorite for the day.
http://www.ebay.com/itm/Shopsmith-10ER-Motor-Pulley-/140682449132?_trksid=p4340.m444&_trkparms=algo%3DPI.WATCH%252BCRX%26its%3DC%252BS%26itu%3DUCC%252BSI%252BUA%252BLM%252BLA%26otn%3D15%26po%3D%26ps%3D63%26clkid%3D5640151550136141389

Ya gotta unnerstan that is half of a matched set!:D
http://www.ebay.com/itm/Shopsmith-10ER-Headstock-Pulley-/140682448147?pt=LH_DefaultDomain_0&hash=item20c153cd13

wiredone · Post by **wiredone** » Mon Jan 16, 2012 12:11 pm

Still haven't sold any of these, although the price is much more realistic.
http://www.ebay.com/itm/140680490697?ss ... 1555.l2649

JPG · Post by **JPG** » Mon Jan 16, 2012 1:28 pm

wiredone wrote:Still haven't sold any of these, although the price is much more realistic.
http://www.ebay.com/itm/140680490697?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

Hey! Why not make a ss pin for a M5/V? Ya would only have to drill one teeny tiny hole in 5/8" ss rod(polished and chamfered).

Ya could probably get $59.95 for them!:D

wiredone · Post by **wiredone** » Mon Jan 16, 2012 8:54 pm

It's already in the works. I want one for my Greenie that's going back together soon.
I don't think I've ever seen a non-rusted factory one!
People for the most part don't realize just how expensive stainless rods are.
I'll shoot a pic and post it when I get er done.

wiredone · Post by **wiredone** » Tue Jan 17, 2012 12:37 pm

That pin on my Greenie is 3/4", are the later ones different? I think I could retail them for 24.95. Think they would sell?

JPG · Post by **JPG** » Tue Jan 17, 2012 1:49 pm

wiredone wrote:That pin on my Greenie is 3/4", are the later ones different? I think I could retail them for 24.95. Think they would sell?

OK! 3/4" My Bad!:o

I am skeptical!

Drill a 1/4-20 centered hole in each end and sell them as double tilt pins.

Trouble is, they never wear out or break!

wiredone · Post by **wiredone** » Tue Jan 17, 2012 7:49 pm

They never wear out but they always rust.
I am ordering some stainless hardware for a dress up on the greenie, I'll put together some kits and see what happens.