Latest member of the stable.

fredsheldon · Post by **fredsheldon** » Sat Mar 02, 2013 1:55 pm

Just finished the restoration of my # 3 10ER, which is currently a dedicated Jig Saw, but will see action as a bowl and pen turning lathe. I now have a 520, 500 and 2 10ER's in my 1/2 of a 2 car garage. My 2nd 10ER is finished but still in pieces. Here is how I store them and then bring them out when working with them.

[ATTACH]20466[/ATTACH]
Completed 10ER restoration that I picked up 3 weeks ago. Just tested it out on a piece of scrap wood and the jig saw works great.

[ATTACH]20467[/ATTACH]
Everything packed away on my side of the garage. My 520, 10ER shorty drill press, 10ER Jig Saw, just acquired Scroll Saw.

[ATTACH]20468[/ATTACH]
Rest of my stuff my ProPlaner and 500 Shorty with dedicated OPR and two backup generators.

[ATTACH]20469[/ATTACH]
When I'm ready to go to work, the wife's car goes out and everything is moved into position. Takes about 2 minutes to move everything back for the night. My work bench is a $15.00 fold up plastic table

joshh · Post by **joshh** » Sat Mar 02, 2013 1:58 pm

Really nice!!

See you tomorrow Fred

JPG · Post by **JPG** » Sat Mar 02, 2013 3:17 pm

Where ya gonna put the 8k 520 etc.?:D

fjimp · Post by **fjimp** » Sat Mar 02, 2013 3:47 pm

Fred,

Is one ER10 set up as a dedicated drill press? I would love to see a better picture of the one that appears as a drill press. I am trying to locate one to use in that manner. Thanks for picture. Jim

fredsheldon · Post by **fredsheldon** » Sat Mar 02, 2013 5:15 pm

fjimp wrote:Fred,

Is one ER10 set up as a dedicated drill press? I would love to see a better picture of the one that appears as a drill press. I am trying to locate one to use in that manner. Thanks for picture. Jim

Jim, here it is.

[ATTACH]20471[/ATTACH]
I cut the base in half, the tubes just overhang the end but since I store it in the upright position it doesn't take up any space. I have since added a speed changer since I took that picture.

mrhart · Post by **mrhart** » Sat Mar 02, 2013 5:55 pm

You have alot of horses in the stable sir. Nice job on the ER's

fjimp · Post by **fjimp** » Sat Mar 02, 2013 6:27 pm

Fred, Thanks again for the picture it gives me an additional idea. I actually thought I had an agreement to purchase one. I just discovered it had been sold to another party. Which is just as well. I am not yet up to messing with one. Jim

algale · Post by **algale** » Sat Mar 02, 2013 7:06 pm

You've got a good start on the Shopsmith Museum!

JPG · Post by **JPG** » Sat Mar 02, 2013 8:00 pm

fredsheldon wrote:Jim, here it is.

[ATTACH]20471[/ATTACH]
I cut the base in half, the tubes just overhang the end but since I store it in the upright position it doesn't take up any space. I have since added a speed changer since I took that picture.

I would be inclined to store the 'tailstock' on the 'top' end.

Nice setup!

fredsheldon · Post by **fredsheldon** » Sat Mar 02, 2013 8:41 pm

joshh wrote:Really nice!!

See you tomorrow Fred

Ok, the seller is taking it apart for us, I hope he doesn't have any issues. Give me a call on my cell, the number I PMed you.

I may go pick it up and have it at my house if you are going to be later than 1:00.