Oh my g**. I never new this unit could run so smooth and quiet. If I was any happier I'd probably be in heaven. When taking the unit apart to perform the upgrade I was amazed how rough and noisy the bearings all were compared to the new ones going into the unit. What an improvement!!! Couldn't be happier!!!New PowerPro
Moderator: admin
New PowerPro
I just received and installed the new PowerPro in my 1973-4 vintage SS Mark V. Oh my g**. I never new this unit could run so smooth and quiet. If I was any happier I'd probably be in heaven. When taking the unit apart to perform the upgrade I was amazed how rough and noisy the bearings all were compared to the new ones going into the unit. What an improvement!!! Couldn't be happier!!!
Oh my g**. I never new this unit could run so smooth and quiet. If I was any happier I'd probably be in heaven. When taking the unit apart to perform the upgrade I was amazed how rough and noisy the bearings all were compared to the new ones going into the unit. What an improvement!!! Couldn't be happier!!!Neal
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
I really have to applaud SS for the great templates they send with this DIY kit. I have never had so many diy drilled holes line up so perfectly, no pushing, twisting or springing to get things lined up. A plus
Neal
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
-
camerio
- Platinum Member
- Posts: 602
- Joined: Fri Aug 11, 2006 8:01 am
- Location: Valcartier, just north of Quebec City, CANADA
Congratulations to you and welcome to the forum.
You should upgrade your Profile so we know where you are from.
I wish I could do the same upgrade soon, but it is not to be yet.
It is offered for us in Mississauga near Toronto but I am far (9hours) from them for service after I do it myself, so I tend to think that I will take the route of an already installed one. Only 400$ difference and I would have my original headstock to fall to if it does not go well.
Otherwise, you give me confidence in the way that you are talking about the templates and the installation going well.
We will see.
You should upgrade your Profile so we know where you are from.
I wish I could do the same upgrade soon, but it is not to be yet.
It is offered for us in Mississauga near Toronto but I am far (9hours) from them for service after I do it myself, so I tend to think that I will take the route of an already installed one. Only 400$ difference and I would have my original headstock to fall to if it does not go well.
Otherwise, you give me confidence in the way that you are talking about the templates and the installation going well.
We will see.
Camerio
MarkV 520 & Band saw
MarkV 520 & Band saw
It was a lot easier than I expected, however did take a fair amount of time as I am one those people who read what to do, check the step about to do, then read it again before doing. I also think I'm one of those people who get a lot of satisfaction from doing something myself.
Neal
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
neal560sl wrote:It was a lot easier than I expected, however did take a fair amount of time as I am one those people who read what to do, check the step about to do, then read it again before doing. I also think I'm one of those people who get a lot of satisfaction from doing something myself.
Getting it done right helps!:D
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
My wife and I visited Quebec City a number of years ago, her grandparents were originally from Frampton. I grew up here in Vermont and my dad owned a small sawmill so I was always used to having want ever lumber I needed when I needed it. He is long since passed and my supply is limited to a small amount of cherry and pine. It sure is different when I have to go buy it now.
Hope to retire in the next couple years and do more woodworking.
Hope to retire in the next couple years and do more woodworking.Neal
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest
Mark V 500, Mark V 500 Power Pro, SS mounted Planer, Jointer, Bandsaw, Belt Sander, Jig Saw, Nova G3, Universal Tool Rest