Dp Table For My Shorty

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

Dp Table For My Shorty

Post by Gene Howe »

If you could see my other table, you'd understand why I needed this.:o :o
The plans came from Woodsmith.
Only modified them so the table would work on the SS.
[ATTACH]22695[/ATTACH]
[ATTACH]22696[/ATTACH]
Attachments
DP table 1.jpg
DP table 1.jpg (68.46 KiB) Viewed 645 times
DP table 2.jpg
DP table 2.jpg (59.45 KiB) Viewed 639 times
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

Sacrificial center section?

I would add something to indicate centering over blade insert slot or center hole.

Nice 'adaptation'. Commode mounting bolts?

Never mind, I just looked at the plans!
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

Post by Gene Howe »

Thanks, JPG.
Please explain your highlighted suggestion. Why would I need to do that?
JPG40504 wrote:Sacrificial center section?

I would add something to indicate centering over blade insert slot or center hole.

Nice 'adaptation'. Commode mounting bolts?

Never mind, I just looked at the plans!
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
Top
User avatar
JPG
Platinum Member
Posts: 35600
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

Gene Howe wrote:Thanks, JPG.
Please explain your highlighted suggestion. Why would I need to do that?

Since the table is referenced to the miter slot, the in/out position of the ss table will make it vary relative to the quill shaft axis.

Now if ya never drill through the table it does not matter, however Murphy says some day that shall come to pass.:eek:

On that day I would prefer none of the ss table top surface be 'on axis'.;)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
Gene Howe
Platinum Member
Posts: 3219
Joined: Wed Jul 26, 2006 7:52 pm
Location: Snowflake, AZ

Post by Gene Howe »

O.K., I see. There are a few holes in one of my older tables.:mad:
Other than the 30" width, the possibility of more holes is why I built the table.
I'm hoping that 1" of material above the table will save the table.;)
Gene

'The true soldier fights not because he hates what is in front of him, but because he loves what is behind him.' G. K. Chesterton
Top
Post Reply

Return to “General Woodworking”