Shhh! You may have just aborted the birth of a heathy baby superstition!!!pieceseeker wrote:If you were reading the text under the picture, it says "Figure 19-4. Two ways to store sanding belts. Don't allow them to kink or become dirty."
I didn't read any where about not letting them become dry, unless of course you can wet sand with them.![]()
![]()
You may not have to break anything!
What is the best way to store sanding belts?
Moderator: admin
- BuckeyeDennis
- Platinum Member
- Posts: 3814
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
- pieceseeker
- Gold Member
- Posts: 370
- Joined: Mon Jan 07, 2013 12:13 pm
- Location: Lawrenceville, Georgia
BuckeyeDennis wrote:Shhh! You may have just aborted the birth of a heathy baby superstition!!!
LOL
That's a good one!:D
" I cut it twice and it's still too short"
2006 Mark 520, 1983 Mark V model 500(soon to be a shorty)/Power Stand mounted Planer/Jointer/Belt Sander/Band Saw/Jigsaw on pwr stand/Scroll saw/Strip Sander/Power Station/Speed Reducer/Increaser/2 Nova chucks.... 12" DeWalt sliding compound mitre saw, 10" Delta tabletop saw, Bosch router and jig saw, Makita circular saw, Graco V-COMP HVLP, Festool CT-26 E Hepa
2006 Mark 520, 1983 Mark V model 500(soon to be a shorty)/Power Stand mounted Planer/Jointer/Belt Sander/Band Saw/Jigsaw on pwr stand/Scroll saw/Strip Sander/Power Station/Speed Reducer/Increaser/2 Nova chucks.... 12" DeWalt sliding compound mitre saw, 10" Delta tabletop saw, Bosch router and jig saw, Makita circular saw, Graco V-COMP HVLP, Festool CT-26 E Hepa
- pieceseeker
- Gold Member
- Posts: 370
- Joined: Mon Jan 07, 2013 12:13 pm
- Location: Lawrenceville, Georgia
That's what I'm talkin about! Looks like a lot of belts to be stored that way. May be a little bit of a hassle to separate, but hey, if you've got a lot of belts!
" I cut it twice and it's still too short"
2006 Mark 520, 1983 Mark V model 500(soon to be a shorty)/Power Stand mounted Planer/Jointer/Belt Sander/Band Saw/Jigsaw on pwr stand/Scroll saw/Strip Sander/Power Station/Speed Reducer/Increaser/2 Nova chucks.... 12" DeWalt sliding compound mitre saw, 10" Delta tabletop saw, Bosch router and jig saw, Makita circular saw, Graco V-COMP HVLP, Festool CT-26 E Hepa
2006 Mark 520, 1983 Mark V model 500(soon to be a shorty)/Power Stand mounted Planer/Jointer/Belt Sander/Band Saw/Jigsaw on pwr stand/Scroll saw/Strip Sander/Power Station/Speed Reducer/Increaser/2 Nova chucks.... 12" DeWalt sliding compound mitre saw, 10" Delta tabletop saw, Bosch router and jig saw, Makita circular saw, Graco V-COMP HVLP, Festool CT-26 E Hepa
- dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
This method, consistent with the way the belts are shipped, appears to be an excellent solution for storage.charlese wrote:Looked for this photo for the last 3 days
http://www.shopsmith.net/forums/attachment.htm?attachmentid=22857&d=1380218917
There is a 4 " wide shelf at the top. Nothing on it.
Selection and handling may be a bit of a hassle but that is of minimal concern.
Thanks for the post.
That, BTW, is the way my belts have been except that I never established a "place". They were here and then they were there. Wherever there was a place for me to discard them that is where they lay.
I used to be organized but no more.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
- robinson46176
- Platinum Member
- Posts: 4182
- Joined: Mon Mar 09, 2009 9:00 pm
- Location: Central Indiana (Shelbyville)
Store them properly???
I consider it a miracle if I can find them!!!
I do have a lot of space up between the joist overhead where I could do the fruit-juice can bit. I might just go that route or something close.
.
I consider it a miracle if I can find them!!!
I do have a lot of space up between the joist overhead where I could do the fruit-juice can bit. I might just go that route or something close.
.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
- dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Only if you have an existing collection of "fruit juice cans". Soft plastic bottles seem to now be the rule. I bemoan the day that I discarded my collection of old coffee cans.robinson46176 wrote:Store them properly???
I consider it a miracle if I can find them!!!![]()
![]()
I do have a lot of space up between the joist overhead where I could do the fruit-juice can bit. I might just go that route or something close.
.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.