Date code and SN on 510

Forum for Maintenance and Repair topics. Feel free to ask questions or contribute.

Moderator: admin

Post Reply
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Date code and SN on 510

Post by "Wild Bad Bob" »

Where is the Date Code and SN on a 510, or is it built into the SN?
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
User avatar
beeg
Platinum Member
Posts: 4790
Joined: Sun Oct 14, 2007 2:33 pm
Location: St. Louis,Mo.

Post by beeg »

Well the SN# should be on the same place as any other. On the silver plate below the aux spindles. What you have is a SS500, with the tables that make it a SS510.
Last edited by beeg on Thu Mar 12, 2015 11:15 am, edited 1 time in total.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

I stumple into a guy this afternoon that has a 510 SN 355510 but does not know how old it is, SS site sez they put a separate date on them instead of listing SN buy date if I understood that right.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
User avatar
beeg
Platinum Member
Posts: 4790
Joined: Sun Oct 14, 2007 2:33 pm
Location: St. Louis,Mo.

Post by beeg »

They DROPPED SN in 1988 and replaced it with a date code.
Last edited by beeg on Thu Mar 12, 2015 11:17 am, edited 1 time in total.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
Top
User avatar
dusty
Platinum Member
Posts: 21530
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Post by dusty »

rbursek wrote:I stumple into a guy this afternoon that has a 510 SN 355510 but does not know how old it is, SS site sez they put a separate date on them instead of listing SN buy date if I understood that right.


Yup. What you have (355510) is a serial number (not a date code). As indicated in this chart (which was posted in response to another of your questions), date codes had not yet come into being. According to the chart, 355510 is a Model 500 that was built probably in late December of 1958. If it is now a 510, someone performed an upgrade that has not been mentioned!

[ATTACH]24833[/ATTACH]

Based on what has been posted here, it is a Greenie with a Gilmer Drive System, a single bearing quill and a 3/4hp motor.
Attachments
Capture, How Old is It.PNG
Capture, How Old is It.PNG (67.64 KiB) Viewed 4498 times
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

Thanks, ends confussion.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
teacherman
Gold Member
Posts: 155
Joined: Sat Mar 01, 2014 8:11 pm

Post by teacherman »

Is there a similar chart for determining the age of SPTs?
Top
User avatar
dusty
Platinum Member
Posts: 21530
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Post by dusty »

teacherman wrote:Is there a similar chart for determining the age of SPTs?

Yes there is, for some. Possibly not for all.

You can find it here by clicking on the top level item that you are interested in and when the page shows, browse down. If available, you will find it.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Top
User avatar
rcplaneguy
Platinum Member
Posts: 549
Joined: Mon Sep 23, 2013 6:33 pm
Location: Chapel Hill, NC

Post by rcplaneguy »

Very cool, thanks Dusty!
John
Top
User avatar
"Wild Bad Bob"
Platinum Member
Posts: 1065
Joined: Fri Mar 28, 2014 2:03 pm
Location: Germantown, Wi

Post by "Wild Bad Bob" »

Thanks Dusty, I missed it thinking it was older newer.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Top
Post Reply

Return to “Maintenance and Repair”