SS table saw blade arbors
Moderator: admin
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
SS table saw blade arbors
I have now had time to focus on all the "stuff" that came with my 3 recent purchases. I have about 7 TS blades on 2 size arbors. Some are SS blades with the arbor designed for just them, and others are on longer arbors designed for a 5/8" arbor hole saw blade. They all have some rust on them and are soaking the threads with some penetrating oil, before I start wrenching on them are they left hand or right hand threads?
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Depends upon the style/nut location.rbursek wrote:I have now had time to focus on all the "stuff" that came with my 3 recent purchases. I have about 7 TS blades on 2 size arbors. Some are SS blades with the arbor designed for just them, and others are on longer arbors designed for a 5/8" arbor hole saw blade. They all have some rust on them and are soaking the threads with some penetrating oil, before I start wrenching on them are they left hand or right hand threads?
If the nut is towards the quill, it is a left handed thread(1 1/4" arbor hole blades).
If the nut is on the outboard side, it is a right handed thread(5/8" arbor hole blades).
Visualize the blade turning normally, then visualize a wrench on the nut. The nut should 'self tighten' with normal blade rotation direction as the wrench is held steady.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Thanks JPG, what a wonderful way to remember and analyze a blade nut thread orientation. I will never forget that rule intentionally, getting old and somethings are out of my control!!!
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.