Good morning gentleman!!!!!!!!! We are back to it. Just having coffee, you have a bit of a jump on me this morning but some here are on ESDST, barring Sunday mornings.
I am going to mic up the thickness of the blades in the greenie and do the same of the ones in the goldie. I think, based on the overall condition and some things still in original boxes and not used of the greenie's "bling things", those blades are original. The goldie if not, have been replaced, based on that they are sitting at the bottom of the cutter head. Curious to see if they say "Disston" on them also.
For your sake and effort Dusty and for future needed info, I will take a bit more time to get a more exact diam measurement of the cutter heads on them. Should be easy, from the underside. I guess it is time to wire up the shop to the internet or go wireless so I am in constant contact with you all, along with a frig, I would have an alternate living space, grill is just outside of the shop too!!LOL I need to run an ASAP errand this morning so after I leave you here after the coffee wined up, I will be back with all that info around 10am ish CSDST.
jointer blade protrusion
Moderator: admin
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Y'all behave this afternoon and stay out of trouble.
I shall be at the 'head'* of an AARP smart driving course.
BTW that is EDT. You are CDT. Dusty is MST.
Ask Dusty to explain that!
* I am 'teaching' it!
I shall be at the 'head'* of an AARP smart driving course.
BTW that is EDT. You are CDT. Dusty is MST.
Ask Dusty to explain that!
* I am 'teaching' it!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
I'm guessing the outfeed table height is not adjustable?
Heath
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
You be right on that, table is not.
I would not expect anything less then you being the instructor JPG, with your monster truck with 5ft diam mudders on it, be patient with the old ladies!!!
Alright, diams of the cutter heads, a bit hard to get at with a 6" veneer calibers, dial version. Goldie 1.975 Greenie 1.985, close enough to know they enlarged them.
Goldie blades .750, never sharpened, made by Disston, same as greenie. Both sets ARE tapered. Dissecting a SS jointer.
Question, on both SS jointers, my Menards Clone, and my MIC free standing one, there is an octagon hole for the guard to mount on the in feed table near the rabbiting table, got that! On all 4 there is a similar hole on the out feed table near the fence area. What for?
I would not expect anything less then you being the instructor JPG, with your monster truck with 5ft diam mudders on it, be patient with the old ladies!!!
Alright, diams of the cutter heads, a bit hard to get at with a 6" veneer calibers, dial version. Goldie 1.975 Greenie 1.985, close enough to know they enlarged them.
Goldie blades .750, never sharpened, made by Disston, same as greenie. Both sets ARE tapered. Dissecting a SS jointer.
Question, on both SS jointers, my Menards Clone, and my MIC free standing one, there is an octagon hole for the guard to mount on the in feed table near the rabbiting table, got that! On all 4 there is a similar hole on the out feed table near the fence area. What for?
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Jointer Table and Finger Guards
rbursek wrote:You be right on that, table is not.
I would not expect anything less then you being the instructor JPG, with your monster truck with 5ft diam mudders on it, be patient with the old ladies!!!
Alright, diams of the cutter heads, a bit hard to get at with a 6" veneer calibers, dial version. Goldie 1.975 Greenie 1.985, close enough to know they enlarged them.
Goldie blades .750, never sharpened, made by Disston, same as greenie. Both sets ARE tapered. Dissecting a SS jointer.
Question, on both SS jointers, my Menards Clone, and my MIC free standing one, there is an octagon hole for the guard to mount on the in feed table near the rabbiting table, got that! On all 4 there is a similar hole on the out feed table near the fence area. What for?
Are you talking about the hole that is shown in this image of yours?
http://www.shopsmith.net/forums/attachment.htm?attachmentid=25274&d=1401642289
Does this answer your question. It is where the safety feather guard mounts.
I have not seen a "Shopsmith Jointer" with holes in the outfeed table top. Maybe someone o the Menard website can help.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
I can't speak for the Shopsmith jointer, but an old Craftsman jointer from the 1930s (very similar to one I'm currently restoring) had two guards.
My only guess to its function is to guard the blade when you've got the fence close to the rabbeting table... for... rabbeting? I don't know. Just a guess.
My only guess to its function is to guard the blade when you've got the fence close to the rabbeting table... for... rabbeting? I don't know. Just a guess.
Heath
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
Central Louisiana
-10ER - SN 13927, Born 1949, Acquired October 2008, Restored November, 2008
-10ER - SN 35630, Born 1950, Acquired April 2009, Restored May 2009, A34 Jigsaw
-Mark V - SN 212052, Born 1986, Acquired Sept 2009, Restored March 2010, Bandsaw
-10ER - SN 39722, Born 1950, Acquired March 2011, awaiting restoration
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
That is a pluasable answer on the rabbiting.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
No Dusty, that is where the guard mounts for normal operation, it is on the out feed table, I will get a pic off after lunch.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Heath is correct. The hole in the outfeed table is for when the fence is moved towards the far side(for rabbiting edges or whatever). The guard is moved there to cover the right end of the exposed cutter head.
The 'current' design accomplishes the covering with a different design since the guard is not east to relocate.
The 'current' design accomplishes the covering with a different design since the guard is not east to relocate.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange