My new ( revised) sanding station

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

My new ( revised) sanding station

Post by charlese »

Here's a photo of my newest sanding station using the PowerPro. It has the Strip Sander and two drum sanders. This set-up is for sanding the newest collection of small cars. The Strip Sander is used for sanding convex surfaces and the drums for concave areas.

The PowerPro is run in reverse at 1300 RPM and all sanding is done without and any changes. The headstock just keeps running and I work from the back side.

All dust is collected - no mess!

[ATTACH]25538[/ATTACH]
Attachments
photo (9).JPG
photo (9).JPG (151.52 KiB) Viewed 4724 times
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Top
User avatar
beeg
Platinum Member
Posts: 4791
Joined: Sun Oct 14, 2007 2:33 pm
Location: St. Louis,Mo.

Post by beeg »

NICE setup Chuck. How MANY cars do you have to sand? How about a lower speed to cut down on heat build up?
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
Top
claimdude
Gold Member
Posts: 458
Joined: Fri Dec 29, 2006 11:47 pm

Post by claimdude »

Neat set up! PowerPro is da bomb!!

Jack
Top
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

Post by charlese »

beeg wrote:NICE setup Chuck. How MANY cars do you have to sand? How about a lower speed to cut down on heat build up?
No heat buildup at all. I only have to sand down the rough spots from bndsawing. How many cars? 100+
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Top
User avatar
dusty
Platinum Member
Posts: 21481
Joined: Wed Nov 22, 2006 6:52 am
Location: Tucson (Wildcat Country), Arizona

Post by dusty »

Yes, a neat setup....but

You said you run in reverse and you work on the backside. I can see that in the setup.

Can you do the same thing working in forward on the front side?
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Top
User avatar
JPG
Platinum Member
Posts: 35438
Joined: Wed Dec 10, 2008 7:42 pm
Location: Lexington, Ky (TAMECAT territory)

Post by JPG »

dusty wrote:Yes, a neat setup....but

You said you run in reverse and you work on the backside. I can see that in the setup.

Can you do the same thing working in forward on the front side?

IF ya can get a drive shaft on the left side of the strip sander(:rolleyes:) , yes.;)
╔═══╗
╟JPG ╢
╚═══╝

Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Top
charlese
Platinum Member
Posts: 7501
Joined: Fri Dec 08, 2006 10:46 pm
Location: Lancaster, CA

Post by charlese »

dusty wrote:...
You said you run in reverse and you work on the backside. I can see that in the setup.

Can you do the same thing working in forward on the front side?
Oh, Yes!- but I happen to have the bandsaw set onto the other end. This way all I need to do to use the bandsaw is remove the two drill chucks and put on a hub and slide the headstock.

The reason I'm running the headstock in reverse is to turn the strip sander in the correct direction.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Top
Post Reply

Return to “General Woodworking”