crab wrote:
crab
See the pony tail on the right hand end in the pic. The quill should be pointing the other way.
Another first Timer - I think I have a 1954 Mark V
Moderator: admin
See the pony tail on the right hand end in the pic. The quill should be pointing the other way.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
beeg wrote:See the pony tail on the right hand end in the pic. The quill should be pointing the other way.
And carriage on the other side of it and reversed on the tubes.]NOPE! My bad!![/color]
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
JPG40504 wrote:And carriage on the other side of it and reversed on the tubes.]NOPE! My bad!![/color]
Just to make it clear. Take the carriage off the way tubes and leave it in the same orientation. Then take the headstock off and turn it around. Reinstall the carriage then the headstock .
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
That is what I FINALLY saw!!! To apologize for!! My bad!!
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
beeg wrote:Just to make it clear. Take the headstock off the way tubes and turn it around. Then take the carriage off and leave it in the same orientation. Reinstall the headstock then the carriage.
I think the sequence of events is slightly different than stated here.
First we must remove the tie bar.
Then I'd take the carriage off knowing that it goes back on in the same orientation.
Then I would take the headstock off, turn it around and reinstall it. WRONG...put the carriage back on before the headstock.
Then I would put the carriage back on.
Last of all, reinstall the tie bar.
That's what Beeg said to do in the beginning.!!!!
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Me too!dusty wrote:I think the sequence of events is slightly different than stated here.
First we must remove the tie bar.
Then I'd take the carriage off knowing that it goes back on in the same orientation.
Then I would take the headstock off, turn it around and reinstall it.
Then I would put the carriage back on.
Last of all, reinstall the tie bar.
Except I would re install the carriage, then the headstock.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
There is a reason I always list stuff as if I was assembling it in drill-press mode.
From bottom to top works the same, whichever side you're looking at.
steve
From bottom to top works the same, whichever side you're looking at.
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
You old men are making my head spin.beeg wrote:See the pony tail on the right hand end in the pic. The quill should be pointing the other way.
I am thinking that you mean that the headstock should be on the right hand side in the above picture, facing the other way ( toward the center). Yeah?I spent a few minutes with a scotch brite this morning and some oil. everything I worked on is turning freely. I have not touched the headstock, as getting our old VW running is my main nights & weekends job right now.
FORGET right hand left hand side.crab wrote:You old men are making my head spin.
I spent a few minutes with a scotch brite this morning and some oil. everything I worked on is turning freely. I have not touched the headstock, as getting our old VW running is my main nights & weekends job right now.
YES the headstock needs to face the other way. BTW, the ponytail is what locks and unlocks the way tubes so you can raise or lower it from the drill press position. Also in the pic, the ponytail is unlocked.SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob