Bill M,
goooooooooooooooood to see ya! here!!!!!!!!!!!!!!!!!
Picked up a 1981 Mark V yesterday.
Moderator: admin
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
[quote="JPG40504"]I do not think the guard in post # 7 needs any drilling etc.]
Hmm, well, you are right, but it's $45 for the old style guard vs $8 for the mounting block (and I get to use my better clear style guard).
I'm still thinking JB Weld would be the way to go. I've used it before and if you do it right it becomes a permanent fixture of whatever you use it on. I've repaired a broken mount on a washing machine. When I finally bought a new washer years later I checked and the weld was still intact. It outlasted the rest of the machine.
Hmm, well, you are right, but it's $45 for the old style guard vs $8 for the mounting block (and I get to use my better clear style guard).
I'm still thinking JB Weld would be the way to go. I've used it before and if you do it right it becomes a permanent fixture of whatever you use it on. I've repaired a broken mount on a washing machine. When I finally bought a new washer years later I checked and the weld was still intact. It outlasted the rest of the machine.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
I fully understand the mindset!;)St8kout wrote:Hmm, well, you are right, but it's $45 for the old style guard vs $8 for the mounting block (and I get to use my better clear style guard).
I'm still thinking JB Weld would be the way to go. I've used it before and if you do it right it becomes a permanent fixture of whatever you use it on. I've repaired a broken mount on a washing machine. When I finally bought a new washer years later I checked and the weld was still intact. It outlasted the rest of the machine.
I have not acquired that opinion of JBWeld.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
My missing parts are on the way. I ordered the screws too just in case I decide to mount the block according to their directions (cutting, drilling, taping). I'll try JB Weld first though.
I also ordered the bandsaw coupler. I wish there were some kind of substitute for this $21 breakable piece of plastic. I even looked for a stiff rubber hose with an internal diameter of 1-1/8" that would breakaway just as easily without the expense. Or something with a cotter key like they use on outboard motor propellers to protect the motor. I've got the bandsaw cleaned and aligned, all ready to go. Just need that plastic coupler.
On a side note, was watching NCIS reruns on my dvr and spotted this on the episode "Alibi." Gibbs finally got a power tool:)
I'm sure someone here will recognize it.
[ATTACH]25954[/ATTACH]
I also ordered the bandsaw coupler. I wish there were some kind of substitute for this $21 breakable piece of plastic. I even looked for a stiff rubber hose with an internal diameter of 1-1/8" that would breakaway just as easily without the expense. Or something with a cotter key like they use on outboard motor propellers to protect the motor. I've got the bandsaw cleaned and aligned, all ready to go. Just need that plastic coupler.
On a side note, was watching NCIS reruns on my dvr and spotted this on the episode "Alibi." Gibbs finally got a power tool:)
I'm sure someone here will recognize it.
[ATTACH]25954[/ATTACH]
- Attachments
-
- Gibbs 236.JPG (108.26 KiB) Viewed 1944 times
-
"Wild Bad Bob"
- Platinum Member
- Posts: 1065
- Joined: Fri Mar 28, 2014 2:03 pm
- Location: Germantown, Wi
Its a scroll saw on an E or ER 10.
Measure once, cut as many times as needed to get it right! Bob
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
56/57 Greenie with jointer, 85 Mark V with band saw, 63 Goldie with jointer, 3 ER 10s, 1951 vintage, Hernia from the Er 10s, Tool Shop SS clone 6" jointer, and 6" belt sander, Delta 10" TS, Buffalo 6" jointer, Craftsman 12" BS, 10" Ryobi planer. Compound Miter, and misc.
Almost. A scroll saw drives the blade in both directions. (Think of a coping saw from High School, except powered.) This is a jigsaw, which pulls down with power, but lifts up with a spring. As an added feature, the upper mount assembly also has a piston, to provide an air source to blow away chips.rbursek wrote:Its a scroll saw on an E or ER 10.
And, Jethro's Model 10 has been verified as a 10ER.
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
See my thread in the "Community" section, about "Jethro Gibbs"ing a Model 10.St8kout wrote: On a side note, was watching NCIS reruns on my dvr and spotted this on the episode "Alibi." Gibbs finally got a power tool:)
I'm sure someone here will recognize it.
[ATTACH]25954[/ATTACH]
I've had 2 different NCIS fans "Jethro Gibbs" my 10ER in my front room. (I'm NOT going to say just how many times I've rested an "adult beverage" on a Model 10 table!):D
Notice that in neither episode where the 10ER showed up with ethanol included, did he actually power up his Shopsmith. Smart man!
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Oh, that "gooseneck light is quite the rarity for a Model 10. I've seen 2 in my life, and currently have one.St8kout wrote: On a side note, was watching NCIS reruns on my dvr and spotted this on the episode "Alibi." Gibbs finally got a power tool:)
I'm sure someone here will recognize it.
[ATTACH]25954[/ATTACH]
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.