Gets very hot in my shop during the summer time and when I returned this fall I found several bubbles under the plastic cover on my control panel. Have any of you experienced this with your PowerPro? Is the top plastic film on the control panel to be removed when the PowerPro is put into service? Machine works well, but the bubbles just look very untidy.
[ATTACH]26621[/ATTACH]
PowerPro.....Bubbles Under Control Panel
Moderator: admin
PowerPro.....Bubbles Under Control Panel
- Attachments
-
- DSCN2834.JPG (82.01 KiB) Viewed 1923 times
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Peel off the plastic sticker!!! (I had the same issue!) it's just there to protect it until installed.
OK, since the subject has been brought up, I've got a question.
Leave that "protective" layer on, until it starts to go "south," or peel it off when you get the device.
I'm thinkin,' once you peel it off, it's not protecting any more, use it while you can.
Right?
Wrong?
Let me know, and also let me know if this is a thread-jack.
steve
Leave that "protective" layer on, until it starts to go "south," or peel it off when you get the device.
I'm thinkin,' once you peel it off, it's not protecting any more, use it while you can.
Right?
Wrong?
Let me know, and also let me know if this is a thread-jack.
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
-
fredsheldon
- Platinum Member
- Posts: 1175
- Joined: Tue Jan 17, 2012 1:31 pm
- Location: The Woodlands, Texas
No wonder my new coffee maker's clock doesn't work. It's always 12:10 PM 
Fred Sheldon
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
The Woodlands, Tx
'52 10ER # 60869 (restored in 2012, used as a dedicated drill press), '52 10ER # 88712 (restored 01/2013), 52 10ER # 71368 (in process of restoring), '83 500 Shorty with OPR installed, '83 520 PowerPro with Lift Assist, 6" Joiner, 6" Belt Sander, 18" Jig Saw, 11" Band Saw, 12" ProPlaner, SS Crosscut Table. SS Dust Collector, Hitachi 1/2" router, Work Sharp 3000 with all attachement, Nova G3 Chuck, Universal Tool Rest, Appalachia Tool Works Sled.
