Greetings, my first post:
My bandsaw started slipping the blade. The tires were old and cracking so I bought two more. As I pull the old ones off I discover the top wheel is very hard to turn.......
The bottom wheel, not attached to the motor, spins freely.
First question: should there be any resistance there?
2nd: if lubricant doesn't do the trick must I dismantle the shroud to access that axle?
3rd: How bout them Patriots eh?
4th: Anybody tried putting tires on the wheels with no glue at all? My old ones had no glue, I'll try the new ones with no glue....
Well thanks then, I'll pace the floor waiting on your response.
bandsaw fixing
Moderator: admin
-
RobLMurphy
- Bronze Member
- Posts: 6
- Joined: Sat Jan 24, 2015 1:10 pm
Re: bandsaw fixing
While you were out I consulted my manual.
There's a retaining ring and a fiber washer on the upper wheel.
Now to figure out how to remove a retaining ring.
Apparently my split ring pliers that I just bought at harbor freight are not going to help because this is not a split ring........
There's a retaining ring and a fiber washer on the upper wheel.
Now to figure out how to remove a retaining ring.
Apparently my split ring pliers that I just bought at harbor freight are not going to help because this is not a split ring........
Re: bandsaw fixing
The top wheel should spin pretty freely. It rides on a needle bearing that needs periodic lube/grease. There's a retaining clip and fabric washer that hold the upper wheel to the upper axle. Remove them, inspect for damage to the axle and needle bearing, lube, replace and see if your problem goes away.
No glue is needed if you are putting on the orange silicone tires. The black rubber tires need rubber cement.
No glue is needed if you are putting on the orange silicone tires. The black rubber tires need rubber cement.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
RobLMurphy
- Bronze Member
- Posts: 6
- Joined: Sat Jan 24, 2015 1:10 pm
Re: bandsaw fixing
Hey thanks. My first ever spiral retaining ring removal and replacement went off and on without a hitch.
Apparently the last guy used wood putty instead of grease on them bearings. I washed them out with WD40 and oiled them up. They spin like freedom.
Now riddle me this: how'd my black rubber tires work for 25 years with no glue? That's when I bought this machine second hand.
On the product review page there's some angry tire buyers kicking the new orange type, and a few more complaining about the glue on the black rubber................
My hands are cold, I'll think on this....
Apparently the last guy used wood putty instead of grease on them bearings. I washed them out with WD40 and oiled them up. They spin like freedom.
Now riddle me this: how'd my black rubber tires work for 25 years with no glue? That's when I bought this machine second hand.
On the product review page there's some angry tire buyers kicking the new orange type, and a few more complaining about the glue on the black rubber................
My hands are cold, I'll think on this....
Re: bandsaw fixing
R Murphy
Can you edit your profile and include your location. You may be close enough to another member that can give some help
Bill V
Can you edit your profile and include your location. You may be close enough to another member that can give some help
Bill V
-
RobLMurphy
- Bronze Member
- Posts: 6
- Joined: Sat Jan 24, 2015 1:10 pm
Re: bandsaw fixing
I'm right here.
Kidding, I'm on Statesboro GA. There's nobody here but me.
I will though update my profile.
Update to my saga coming soon.
Kidding, I'm on Statesboro GA. There's nobody here but me.
I will though update my profile.
Update to my saga coming soon.
-
RobLMurphy
- Bronze Member
- Posts: 6
- Joined: Sat Jan 24, 2015 1:10 pm
Re: bandsaw fixing
bet you couldn't wait to see how it all worked out.
well so far it hasn't. That tire doesn't stretch well when it's cold.
To be continued.........
well so far it hasn't. That tire doesn't stretch well when it's cold.
To be continued.........
Re: bandsaw fixing
Maybe the glue just dried up and came off with the old tire. Certainly the new rubber tire kit comes with glue.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: bandsaw fixing
55 degrees and your hands are cold? 
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: bandsaw fixing
RobLMurphy wrote:I washed them out with WD40 and oiled them up. They spin like freedom.
Now pack the needle bearings with grease.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob