Restoring 10ER S/N 83974
Moderator: admin
Re: Restoring 10ER S/N 83974
The motor stator housing is painted and the motor is back together with new OEM bearings. I also burnished the start winding switch contacts.
- Attachments
-
- IMAG0190.jpg (185.59 KiB) Viewed 13364 times
-
- IMAG0192.jpg (149.18 KiB) Viewed 13364 times
-
- IMAG0193.jpg (148.32 KiB) Viewed 13364 times
-
- IMAG0194.jpg (153.33 KiB) Viewed 13364 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Restoring 10ER S/N 83974
That looks better than new. Enjoying this thread even though I don't have an 10ER.
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
JPG
- Platinum Member
- Posts: 35598
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Restoring 10ER S/N 83974
Geez! Now I have to go paint a motor etc.! 
Well done!
Well done!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Restoring 10ER S/N 83974
Thanks guys it has been a lot of fun. More fun on the way. I have 4 more here.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: Restoring 10ER S/N 83974
Here are the castors. They were completely taken apart, sorry no pics of that. One thing to know, when you remove the roll pins mark all parts to go back together exactly as original. Including the 180 degree orientation of the two rods. They are NOT drilled all the same. Don't ask me how I know.
- Attachments
-
- DSCF0982.JPG (346.49 KiB) Viewed 13352 times
-
- DSCF0984.JPG (312.72 KiB) Viewed 13352 times
-
- DSCF0985.JPG (329.12 KiB) Viewed 13352 times
-
- DSCF0988.JPG (347.29 KiB) Viewed 13352 times
-
- DSCF0992.JPG (323.83 KiB) Viewed 13352 times
-
- DSCF0993.JPG (295.93 KiB) Viewed 13352 times
-
- DSCF0995.JPG (318.88 KiB) Viewed 13352 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
JPG
- Platinum Member
- Posts: 35598
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Restoring 10ER S/N 83974
I do not need to ask! 
BTW, did the foot pedal retaining pins have 'through' holes? Mine were in a blind hole.
BTW, did the foot pedal retaining pins have 'through' holes? Mine were in a blind hole.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Restoring 10ER S/N 83974
JPG wrote:I do not need to ask!
BTW, did the foot pedal retaining pins have 'through' holes? Mine were in a blind hole.
Yes, they were drilled through. If they were not I don't know how you would get them off. Probably have to take them to a machine shop and have them EDMd out and then drill the hole through. That way the guy 60 years from now can punch them through. John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
JPG
- Platinum Member
- Posts: 35598
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Restoring 10ER S/N 83974
I drilled through the center of the tension pin a small hole all the way through. Used that hole as a pilot/alignment and drilled from the opposite side up to the inside end of the pin. Then drove the pin through.
Documented somewhere here(way back when).
Documented somewhere here(way back when).
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Restoring 10ER S/N 83974
Al, check Craigslist.algale wrote:That looks better than new. Enjoying this thread even though I don't have an 10ER.
That has been MY downfall.
(See my sig, for the bad news. Yes,
I am looking for one more. Don't ask
why, because I don't know!)
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
-
KenWilliams
- Bronze Member
- Posts: 1
- Joined: Tue Sep 08, 2015 1:52 pm
Re: Restoring 10ER S/N 83974
I have a 1950 shop smith ER10(?) that I have just pulled a boo boo on!!
I am asking for some tech.assistance from anyone with experience on this modal ss. Dilema: I have apparently extended the drill bit too far while attempting to drill through a 2x6 and the drill will no longer retract!!
How can I "re-attach" the drive mechanism to make the drill to retract??
Any assistance provided would be greatly appreciated.
Thank you,
Ken Williams
615-791-7711
Franklin, TN
I am asking for some tech.assistance from anyone with experience on this modal ss. Dilema: I have apparently extended the drill bit too far while attempting to drill through a 2x6 and the drill will no longer retract!!
How can I "re-attach" the drive mechanism to make the drill to retract??
Any assistance provided would be greatly appreciated.
Thank you,
Ken Williams
615-791-7711
Franklin, TN