- Photo Dec 18, 8 23 46 AM.jpg (1.01 MiB) Viewed 3012 times
- Photo Dec 18, 8 52 44 AM.jpg (922.51 KiB) Viewed 3012 times
- Photo Dec 18, 9 46 32 AM.jpg (1.06 MiB) Viewed 3012 times
Mark 2
Moderator: admin
-
tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Mark 2
I found this Mark 2 locally and the price was right so I bought myself a little present. I have plans for many of the parts. The jacobs chuck required a little work but once it was off I could remove the pulley cover. I was surprised it actually runs. It would not run at the seller's house. Letting it warm up over night seems to have helped a lot. Fun and interesting so far!
[youtube]https://www.youtube.com/watch?v=0cApABAlqiY[/youtube]
[youtube]https://www.youtube.com/watch?v=0cApABAlqiY[/youtube]
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark 2
Take VERY good care of the belt cover!!!
Belt dressing will help.
Belt dressing will help.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
masonsailor2
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: Mark 2
Very cool !
-
tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Re: Mark 2
Polishing the way tubes using Norton sponge abrasive 100, 180, 220. Pretty easy to do by hand even though I have not yet set up a lathe operation for that.
- Photo Dec 18, 12 22 59 PM.jpg (843.87 KiB) Viewed 2961 times
- Photo Dec 18, 12 35 54 PM.jpg (787.97 KiB) Viewed 2961 times
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark 2
Got the vertical lock figgered out?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Re: Mark 2
Not till you mentioned it. Thanks! I was wondering what the heck that bracket was for. Do you have a Mark 2?JPG wrote:Got the vertical lock figgered out?
- Photo Dec 18, 1 49 17 PM.jpg (895.33 KiB) Viewed 2927 times
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark 2
I have 'pieces' put together as a portable.
No M2 headstock - use an old greenie headstock.
Made base that mounts on horses.
Have all the upper pieces except aux table/tail stock, but the Mark 5/V stuff all fits.
Some stuff a bit small, but it works.
Some folks look down on it and do so somewhat justifiably, but it is useful.
$ well invested IMHO.
No M2 headstock - use an old greenie headstock.
Made base that mounts on horses.
Have all the upper pieces except aux table/tail stock, but the Mark 5/V stuff all fits.
Some stuff a bit small, but it works.
Some folks look down on it and do so somewhat justifiably, but it is useful.
$ well invested IMHO.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: Mark 2
I didn't realize the belt drive system simular to a 10ER. That's cool, like they were admitting that the 10ER drive was functional after all .... 
I may have to go find one ....
I may have to go find one ....
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Mark 2
Although the trunion is the same as a Mark 5, the mounting posts are 'smooth' and is secured by brass screws on each. Also the table raising crank Ala ER.rjent wrote:I didn't realize the belt drive system simular to a 10ER. That's cool, like they were admitting that the 10ER drive was functional after all ....
I may have to go find one ....
A 'modified' ER speed changer would be intriguing.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Re: Mark 2
I hear you Dick. I want a 10ER now.rjent wrote:I may have to go find one ....