Do you use evaporative coolers to cool your shop?
Moderator: admin
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Do you use evaporative coolers to cool your shop?
@ Ed in Tampa, on This Old House they have put some Geothermals in but never said what the pay back time was for the expense over conventional. I like the technology of it, but payback if done by a commercial out fit must be a decade or so. I compare that to a tankless water heater, initial cost is more, has to be flushed and cleaned ever year, or should be, higher BTUs used than a heated tank, at firing time time, and during usage, ect.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
- BuckeyeDennis
- Platinum Member
- Posts: 3813
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Do you use evaporative coolers to cool your shop?
I can't get natural gas where I live, and propane was recently sky-high .. about the same as electric resistance heating. So a couple of years ago, I got a quote on a geothermal system from a reputable company. The system cost was upwards of $20 grand, even after tax credits. Not counting dealing with the mess it would have made of my yard.Ed in Tampa wrote:Why not use an air conditioner or a Geothermic heat pump?
The company estimated a payback period of about 6 years. But I had good records of my historical energy usage, and they had overestimated my heating needs considerably. The actual payback period would have been about ten years.
The good news is that the natural gas company now seems serious about running lines into my area. And that's only about a third the cost of the alternatives.
- tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Re: Do you use evaporative coolers to cool your shop?
Dusty, your results fall pretty much in line with the map in Everett's first post. Mississippi and Dallas, Texas are both in Area C, not recommended for swamp coolers. Arizona may be better in season.dusty wrote:When the humidity is up, swamp coolers are a waste. Just sit in front of a fan. I base my comment on summers in Mississippi for four years. Dallas Texas wasn't much better. Arizona, during monsoon season, is just as bad.
- tomsalwasser
- Platinum Member
- Posts: 928
- Joined: Mon Feb 08, 2010 2:09 pm
Re: Do you use evaporative coolers to cool your shop?
You are welcome ER. You won't find swamp coolers in St Paul or Germantown. Anything you want to know there is fact or fiction to be found on youtube!ERLover wrote:Thanks Tom, for the you tube I am now an expert on Swamp Coolers.
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Do you use evaporative coolers to cool your shop?
All I know is moms/dads house was built in 1966, about a 3K sq ft ranch, original windows and doors, in the shade most of the time, attached garage on the north side, garage has insulated walls and ceiling, not open rafters, with insulation but does get the sun in summer around 2-3pm till about 6pm.
It has been 90* here the past few days, at about 10pm I turn the central AC to 68*, when I get up around 7-8ish am, turn it up to 74*, it does not kick back on till about 3-4pm.
It has been 90* here the past few days, at about 10pm I turn the central AC to 68*, when I get up around 7-8ish am, turn it up to 74*, it does not kick back on till about 3-4pm.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.