OH boy! Now I'm nervous.
Thanks for the warning. I guess I never took it that far apart before.
Slow to gain speed
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Slow to gain speed
Start at about the 7 minute mark.beerboss wrote:OH boy! Now I'm nervous.
Thanks for the warning. I guess I never took it that far apart before.
http://www.shopsmithacademy.com/SS_Arch ... rn_Pt2.htm
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Slow to gain speed
Will do, thanks so much!!!
Re: Slow to gain speed
JPG wrote:beerboss wrote:Thanks, I'll give it a shot. I think I will take it apart, it has been a few years since I revived it anyway.
Beware that spring!!!!!
Research the removal(and reassembly) method before attempting.
his may help ya with the spring removal/reinstall.
replacing the motor spring.PDF- (292.02 KiB) Downloaded 575 times
Ya might need this also.
- how to do a high speed adjustment.PDF
- (382.25 KiB) Downloaded 533 times
Last edited by beeg on Wed Aug 24, 2016 4:19 pm, edited 1 time in total.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
Re: Slow to gain speed
If I'm going to go through all this would you suggest I replace the spring as well? Or will just cleaning everything up be sufficient?
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Slow to gain speed
beerboss wrote:If I'm going to go through all this would you suggest I replace the spring as well? Or will just cleaning everything up be sufficient?
If it ain't broke, don't replace it.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Slow to gain speed
My hero! Not that I don't mind buying a new tool now and again but a spring...
Re: Slow to gain speed
I was going to say the problem seems to be in the moveable sheave on the motor shaft. JPG beat me to it.
The best way I have found to truly lube this - is to put the machine in drill press position. Secure the belt cover up to the top with a string or clamp. Pull out the moveable sheave by hand - DON'T LET IT SLAM BACK INTO CLOSED POSITION. Slide the sheave back and forth several times oiling the shaft as you do. You will probably find the sheave moving easier as oil penetrates.
This may be easier for you in standard sawing position. but the vertical position will allow oil to run into the small space between the motor shaft and the sheave tube.
A few drops in the oil hole are just not enough.
The best way I have found to truly lube this - is to put the machine in drill press position. Secure the belt cover up to the top with a string or clamp. Pull out the moveable sheave by hand - DON'T LET IT SLAM BACK INTO CLOSED POSITION. Slide the sheave back and forth several times oiling the shaft as you do. You will probably find the sheave moving easier as oil penetrates.
This may be easier for you in standard sawing position. but the vertical position will allow oil to run into the small space between the motor shaft and the sheave tube.
A few drops in the oil hole are just not enough.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
Re: Slow to gain speed
Put the speed control to FAST gives the best results and in the drill press position. You cannot over oil the headstock.charlese wrote:I was going to say the problem seems to be in the moveable sheave on the motor shaft. JPG beat me to it.
The best way I have found to truly lube this - is to put the machine in drill press position. Secure the belt cover up to the top with a string or clamp. Pull out the moveable sheave by hand - DON'T LET IT SLAM BACK INTO CLOSED POSITION. Slide the sheave back and forth several times oiling the shaft as you do. You will probably find the sheave moving easier as oil penetrates.
This may be easier for you in standard sawing position. but the vertical position will allow oil to run into the small space between the motor shaft and the sheave tube.
A few drops in the oil hole are just not enough.
Re: Slow to gain speed
Great, I'll try this first.