So yesterday I glued up the sandwich for the lid and today I got it made. All that is left is finishing.
I-Box Box
Moderator: admin
Re: I-Box Box
Well, I finally worked on the box again. I didn't realize how long it has been. The holdup was needing to get some more Black Walnut. My wife had a scroll saw project that she wanted to use Black Walnut so we went and got some.
So yesterday I glued up the sandwich for the lid and today I got it made. All that is left is finishing.
So yesterday I glued up the sandwich for the lid and today I got it made. All that is left is finishing.
- Attachments
-
- IMAG0538.jpg (188.63 KiB) Viewed 10219 times
-
- IMAG0540.jpg (130.4 KiB) Viewed 10219 times
-
- IMAG0541.jpg (178.83 KiB) Viewed 10219 times
-
- IMAG0542.jpg (159.85 KiB) Viewed 10219 times
-
- IMAG0544.jpg (192.57 KiB) Viewed 10219 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
masonsailor2
- Platinum Member
- Posts: 1564
- Joined: Wed Feb 05, 2014 11:57 am
- Location: Las Vegas NV
Re: I-Box Box
Nice work John. Beautiful joinery !
Paul
Paul
Re: I-Box Box
Thanks Paul. The I Box does an almost perfect job when dialed in properly.masonsailor2 wrote:Nice work John. Beautiful joinery !
Paul
- Attachments
-
- IMAG0462.jpg (134.96 KiB) Viewed 10212 times
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: I-Box Box
How long did it take to learn? I've had mine a couple of years and have not yet used it except to play around with it! This weeken for sure. Just used a gift certificate at my local hardwood store. Got some nice Honduran Mahagony, some cherry and some dloodwood. Three boards, $153.00!
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
rjent
- Platinum Member
- Posts: 2121
- Joined: Fri Mar 14, 2014 3:00 pm
- Location: Hot Springs, New Mexico
Re: I-Box Box
What a gorgeous box John. Nice work. I may have to spring for one of those jigs. Although I kind of like doing it like I have been doing it.
Beautiful!
Beautiful!
Dick
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
1965 Mark VII S/N 407684
1951 10 ER S/N ER 44570 -- Reborn 9/16/14
1950 10 ER S/N ER 33479 Reborn July 2016
1950 10 ER S/N ER 39671
1951 jigsaw X 2
1951 !0 ER #3 in rebuild
500, Jointer, Bsaw, Bsander, Planer
2014 Mark 7 W/Lift assist - 14 4" Jointer - DC3300
And a plethora of small stuff .....
"The trouble with quotes on the Internet is that you can never know if they are genuine." - Benjamin Franklin
Re: I-Box Box
ChrisNeilan wrote:How long did it take to learn? I've had mine a couple of years and have not yet used it except to play around with it! This weeken for sure. Just used a gift certificate at my local hardwood store. Got some nice Honduran Mahagony, some cherry and some dloodwood. Three boards, $153.00!
I just bought 9 BF of 4/4 walnut (10' X 11") and 12 BF of 4/4 Maple (12' X 12"). $170.90. The Walnut was $10.73/BF and the Maple was $5.25/BF.As far as learning it was pretty simple. I watched the video a few times and then had the printed instructions in front of me when I first played with it. If you remember Charlses challenge from my other thread about an 18" long joint with 1/4" pins, that was the third time I tried it. The box in this thread was the next time.
I also bought the package with the Forrest box joint blades. There is nothing better. Equal, maybe but nothing better than Forrest IMO.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: I-Box Box
More then very nice John!! Nice contrasting wood and clean, crisp lines and joints. What is an I box, or is that the name of a jig for cutting the box joints? Rockler has one for the router, I am not sure if it can be used on a TS with the miter gauge, inconjuction with a dado blade.
CN, my wood store is charging $7.00 for 4/4 BW, and anything over 10" wide, gets a 10 or 20% Wide Board up charge.
CN, my wood store is charging $7.00 for 4/4 BW, and anything over 10" wide, gets a 10 or 20% Wide Board up charge.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: I-Box Box
Thank you! The I Box works very well and for me the learning curve was short. I would recommend it to everyone.rjent wrote:What a gorgeous box John. Nice work. I may have to spring for one of those jigs. Although I kind of like doing it like I have been doing it.
Beautiful!
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
Re: I-Box Box
It is an Incra I Box jig made for the table saw. It comes with miter bars for standard table saws and for Shopsmith.ERLover wrote:More then very nice John!! Nice contrasting wood and clean, crisp lines and joints. What is an I box, or is that the name of a jig for cutting the box joints? Rockler has one for the router, I am not sure if it can be used on a TS with the miter gauge, inconjuction with a dado blade.
CN, my wood store is charging $7.00 for 4/4 BW, and anything over 10" wide, gets a 10 or 20% Wide Board up charge.
http://www.incra.com/precision_fences-ibox.html
I use it with the Forrest box joint blade set.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
Eagle's Lair Woodshop
Hooper, UT
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: I-Box Box
Similar to this?
http://www.rockler.com/rockler-router-t ... -joint-jig
I am not a dado guy, when I need dado work I use my router table and some times in conjunction with the table saw regular blade. I just never got into dado blades, there fine tuning for width. I am just more comfortable on the router table with the correct bit.
http://www.rockler.com/rockler-router-t ... -joint-jig
I am not a dado guy, when I need dado work I use my router table and some times in conjunction with the table saw regular blade. I just never got into dado blades, there fine tuning for width. I am just more comfortable on the router table with the correct bit.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.