Allen threaded insert

[pilvr83]

While looking for my carriage lock nut I found this threaded insert but cannot find its home.

It is not for the way tubes, I looked.

I have the infeed/outffeed table brackets (555997), I found four of these type with the set. I checked the table extension legs they have all hardware.

This is a picture. It fits our Allen tool, so it must be for the shopsmith. I found it under the shopsmith.



Any clue?

IMG_20161102_1637591_rewind_kindlephoto-1337665.jpg (54.95 KiB) Viewed 7550 times

[jsburger]

While looking for my carriage lock nut I found this threaded insert but cannot find its home.

It is not for the way tubes, I looked.

I have the infeed/outffeed table brackets (555997), I found four of these type with the set. I checked the table extension legs they have all hardware.

This is a picture. It fits our Allen tool, so it must be for the shopsmith. I found it under the shopsmith.



Any clue?
IMG_20161102_1637591_rewind_kindlephoto-1337665.jpg

The exact thing happened to me 10 or so years ago. I found a set screw under the Shopsmith when I moved it at the end of the day. I kept it in a pill bottle on a shelf of a LONG time but never found where it came from. That SS has since been upgraded to a 520 and then a MK 7 with a Power Pro head stock and double tilt. Never found a missing set screw.

[dusty]

According to my cheat sheet of set screws, the only 1" long flat point set screw is used on the band saw table.

Band Saw Table (Table Tilt) #91 516571 5/16”-18x1” Black Oxide Alloy Steel Flat Point Socket Head Screw

This set screw was at one time item # 86.

http://www.shopsmith.com/ownersite/manuals/845541.pdf (depicted on page 2)

[jsburger]

According to my cheat sheet of set screws, the only 1" long flat point set screw is used on the band saw table.

Band Saw Table (Table Tilt) #91 516571 5/16”-18x1” Black Oxide Alloy Steel Flat Point Socket Head Screw

This set screw was at one time item # 86

OK, but the one in the picture is only 1/2" long.

[dusty]

According to my cheat sheet of set screws, the only 1" long flat point set screw is used on the band saw table.

Band Saw Table (Table Tilt) #91 516571 5/16”-18x1” Black Oxide Alloy Steel Flat Point Socket Head Screw

This set screw was at one time item # 86

OK, but the one in the picture is only 1/2" long.

You are so right. I am still learning how to read a ruler.

The list of 1/2" long set screws is a bit less definitive.

Shopsmith Setscrews Version 10.doc

(119 KiB) Downloaded 569 times

[pilvr83]

According to my cheat sheet of set screws, the only 1" long flat point set screw is used on the band saw table.

Band Saw Table (Table Tilt) #91 516571 5/16”-18x1” Black Oxide Alloy Steel Flat Point Socket Head Screw

This set screw was at one time item # 86

OK, but the one in the picture is only 1/2" long.

You are so right. I am still learning how to read a ruler.

The list of 1/2" long set screws is a bit less definitive.

Shopsmith Setscrews Version 10.doc

I am the one that needs help with rulers. I should have put the insert on the left of the one inch, sorry

[dusty]

OK, but the one in the picture is only 1/2" long.

You are so right. I am still learning how to read a ruler.

The list of 1/2" long set screws is a bit less definitive.

Shopsmith Setscrews Version 10.doc

I am the one that needs help with rulers. I should have put the insert on the left of the one inch, sorry

No! I don't think so. That set screw is very clearly not 1" long. Hope you find its home.

[JPG]

Did you check for the rip fence biasing screws?

[joedw00]

Had the same happen to me about 3 years ago, never did find where it went. Must not have needed it because it still works great.

[ERLover]

Maybe not from the SS, a rabbit hole rejection that ended up there.