Drum Sander

[Hobbyman2]

I don't know nut I suspect that the procedures are not all the same between the 4 different Forum configurations. Which ate you using.
====

???????
How do I check ?

I have read every thing on the forum site from top to bottom ?


Pictures came from a g-3 ,I have noticed when I load pictures on photobucket it also allows the folder to be viewed as a slide show.You can go back and add to or delete the pictures there any time , .

I am only familiar with a forum provided by stintz ..?

It doesnt allow for posting pictures so we use alternate sites to create hyperlinks.

I will double check,,,, however,,,, I am pretty sure I am using a program in the computer called picassa?



Thats all I know about pictures and posting them.


Thanks for the help.

Hobbyman2

[dusty]

I have tinkered with this a bit since I asked the question and I don't believe the version being used makes a technical difference.

However, when you log in, do you change preferences. One of the options is (preferences) is to select one of four different forum forms.

The choices are: prosilver, shopsmith. shopsmith1 and subsilver2.

I much prefer prosilver.

[Hobbyman2]

However, when you log in, do you change preferences. One of the options is (preferences) is to select one of four different forum forms.

The choices are: prosilver, shopsmith. shopsmith1 and sunsilver2.

===========

I just use the default setting .

I will keep playing with this .

I think the upload may be trying to upload all the pictures instead of just one.

Thanks for your help I greatly appreciate it.

Hobbyman2

[ecom1]

FWIW, I was having trouble in the beginning too - then I read a Dusty comment about using a different Forum preference. After I switched to what he was using, I had no trouble posting pics.

[dusty]

However, when you log in, do you change preferences. One of the options is (preferences) is to select one of four different forum forms.

The choices are: prosilver, shopsmith. shopsmith1 and sunsilver2.

===========

I just use the default setting .

I will keep playing with this .

I think the upload may be trying to upload all the pictures instead of just one.

Thanks for your help I greatly appreciate it.

Hobbyman2

No! Only what you select to be uploaded is uploaded.

No matter which format you use, pay close attention to pixel and picture size. The system is unforgiving in that area. Violate the limits and it WILL NOT UPLOAD. In all cases, however, you will get a messge that defines your problem.



The default setting??? What does that happen to be. I have always thought it was the last setting that the user selected.

This is my forum preference and I hardly ever change it.

[Hobbyman2]

It was shopsmith

I changed it to sunsilver , Thanks I like this even better.

I have seen the pixel size in one of the boxes that I got to pop up,,,, however it wouldnt allow any changes, I am learning.

Thanks.

[jsburger]

It was shopsmith

I changed it to sunsilver , Thanks I like this even better.

I have seen the pixel size in one of the boxes that I got to pop up,,,, however it wouldnt allow any changes, I am learning.

Thanks.

You have to change the picture size on your computer and then save it in the new size. Then upload it.

[Hobbyman2]

new pics 038.jpg (40.76 KiB) Viewed 10229 times

new pics 041.jpg (39.38 KiB) Viewed 10229 times

new pics 042.jpg (25.5 KiB) Viewed 10229 times

new pics 043.jpg (36.03 KiB) Viewed 10229 times

new pics 046.jpg (32.39 KiB) Viewed 10229 times

new pics 044.jpg (37.44 KiB) Viewed 10229 times

new pics 047.jpg (41.71 KiB) Viewed 10229 times

So far this is where I am at

Not sure if I am going to do some thing else or not yet.

[Hobbyman2]

I have some rather thick and heavy walnut with live edge that may be a challenge to feed on a angle ,I would rather the table be flat .

One reason I was looking into this is do to stock too wide for most planers.

Hobbyman2

[dusty]

It was shopsmith

I changed it to sunsilver , Thanks I like this even better.

I have seen the pixel size in one of the boxes that I got to pop up,,,, however it wouldnt allow any changes, I am learning.

Thanks.

You have to change the picture size on your computer and then save it in the new size. Then upload it.

Here is going the other way.

Dust Collector r4 018 (Mobile).jpg (41.02 KiB) Viewed 10218 times

Dust Collector r4 018.jpg (1.95 MiB) Viewed 10217 times

Please don't look too closely at the messy shop (especially the floors). I have life time collection of tools in a small garage shop and it always looks like this. If I dumped all the buckets that I have sitting around in there, you would not believe what there is that you cannot see.