The radial arm saw that I have had for 40+ years finally died and I replaced it with a 12" compound sliding miter saw. I had just bought a Freud 10" blade for the ras that does great and I have used very little. Can I use it on the tablesaw without it being dangerous?
It is item number LU91R010' ... grind ATB.. kerf .090.. 60T.. Hook Angle -5* ..
Will that hook angle cause kickback or "lift" ? The cross cut blade I am using now is showing its age so I'd sure like to put this $80+ Freud blade to use.
Can I use a -5* radial saw blade on SS table saw
Moderator: admin
Can I use a -5* radial saw blade on SS table saw
Bill
Mark V 1981 upgraded to 520 and PowerPro, w/ Band Saw, Belt Sander, Jointer, Jigsaw, and a bunch of previous owners 1980's jigs, accessories, and unknown parts.
Mark V 1981 upgraded to 520 and PowerPro, w/ Band Saw, Belt Sander, Jointer, Jigsaw, and a bunch of previous owners 1980's jigs, accessories, and unknown parts.
-
dusty
- Platinum Member
- Posts: 21530
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Can I use a -5* radial saw blade on SS table saw
It is WISE that you ask. I don't know because I have never used a RAS but there rings a bell in the back of my head. Something about what is done to the blade to keep it from climbing with used on a RAS.
Have you read whatever Freud says about the blade. They are good about publishing information, especially safety information, for their blades.
www.freudtools.com
Have you read whatever Freud says about the blade. They are good about publishing information, especially safety information, for their blades.
www.freudtools.com
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Can I use a -5* radial saw blade on SS table saw
Do it!!!!
- clipboard.jpg (28.26 KiB) Viewed 1798 times
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Can I use a -5* radial saw blade on SS table saw
I found this page that explains hook angles.
http://www.carbideprocessors.com/pages/ ... ngles.html
Give it a look and I think that you will find your answer.
Bill V
http://www.carbideprocessors.com/pages/ ... ngles.html
Give it a look and I think that you will find your answer.
Bill V