Have a person who has a mark v and it bogs down when cutting on table saw position. The motor runs he say but wonder if it a belt slipping or something else? Anyone have suggestions?
Thanks,
Tom
Motor slowing down
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Motor slowing down
Poly-V belt slipping.woodmeister wrote:Have a person who has a mark v and it bogs down when cutting on table saw position. The motor runs he say but wonder if it a belt slipping or something else? Anyone have suggestions?
Thanks,
Tom
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: Motor slowing down
is the proper way to tighten it by rotating the eccentric clock wise direction? About 930 - 1000 O'clock position?
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Motor slowing down
Rotate CW until it does not slip.woodmeister wrote:is the proper way to tighten it by rotating the eccentric clock wise direction? About 930 - 1000 O'clock position?
If it gets to 12, the belt needs to be replaced.
Do NOT over tighten the clamping screw.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
woodmeister
- Gold Member
- Posts: 320
- Joined: Fri Sep 11, 2015 5:46 pm
Re: Motor slowing down
THANK YOU