I have a dumb question. I have a Mark V mounted planer. Looking at it logic seems to indicate that I mount it on the right side of the power head when standing on the control side of the power head. This way all of the power switches are on the same side.
The picture of the planer in the catalog has it on the other side of the power head. I don't ave a manual so I need to ask.
Mounting the Mark V Planer
Moderator: admin
-
Steamdragon
- Gold Member
- Posts: 137
- Joined: Sat Aug 01, 2015 12:50 am
- Location: San Jose, CA
Re: Mounting the Mark V Planer
It is mounted on the same side as you would mount the jointer or bandsaw.
Dick
Dick
Re: Mounting the Mark V Planer
Not having a Pro Planer, I can only look at the catalog photo and try to understand.
'the catalog photo has the planer mounted on the accessory side as you observe. Also the planer's infeed side is facing the rear of the Mark 5.
It appears that mounted this way the rotation of the attached coupler is top away from you - or counter clockwise. If mounted on the spindle side but facing the front, the rotation would be reversed. top toward you.
Now I understand why the electronic chart on the PowerPro says select reverse.
THIS WAS EDITED BECAUSE AS USUAL I HAD IT BACKWARDS THE FIRST TIME
'the catalog photo has the planer mounted on the accessory side as you observe. Also the planer's infeed side is facing the rear of the Mark 5.
It appears that mounted this way the rotation of the attached coupler is top away from you - or counter clockwise. If mounted on the spindle side but facing the front, the rotation would be reversed. top toward you.
Now I understand why the electronic chart on the PowerPro says select reverse.
THIS WAS EDITED BECAUSE AS USUAL I HAD IT BACKWARDS THE FIRST TIME
Last edited by charlese on Mon Aug 07, 2017 4:10 pm, edited 2 times in total.
Octogenarian's have an earned right to be a curmudgeon.
Chuck in Lancaster, CA
Chuck in Lancaster, CA
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
'WHY' the planer is mounted on the 'left' end of the headstock.
First that provides the correct rotation for the cutters(plow cutting).
Yes that means infeed side is from the 'back'.
As such the planer power switch(THAT TURNS THE HEADSTOCK MOTOR ON/OFF) needs to also be mounted there.
All that changes with the power pro - reversible so it can mount on the quill end - and the power safety switch becomes redundant(also undesirable unless you like to go through powerpro boot up each time you turn it off/on) because the infeed side is now on the headstock power switch side. It also means a separate power plug for the feed motor(especially if running the PP at 230v).
A lot to consider re 'why'.
Not a dumb question at all!!!!
Yes that means infeed side is from the 'back'.
As such the planer power switch(THAT TURNS THE HEADSTOCK MOTOR ON/OFF) needs to also be mounted there.
All that changes with the power pro - reversible so it can mount on the quill end - and the power safety switch becomes redundant(also undesirable unless you like to go through powerpro boot up each time you turn it off/on) because the infeed side is now on the headstock power switch side. It also means a separate power plug for the feed motor(especially if running the PP at 230v).
A lot to consider re 'why'.
Not a dumb question at all!!!!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
br549
- Platinum Member
- Posts: 657
- Joined: Sun Nov 30, 2014 8:51 am
- Location: Midway between Houston/Galveston, TX
Re: Mounting the Mark V Planer
Shopsmith offers the manual for sale, but a lot of the infomation in the manual is also available free under Woodworking Resources/Online Information/Illustrated Tips:Steamdragon wrote:I don't [h]ave a manual so I need to ask.
http://www.woodshoptips.com/tips/101402/index.htm
and
http://www.woodshoptips.com/tips/030705/index.htm