That should be irrelevant.kd6vpe wrote:What ever happened here anything? Mine just died and have taken it apart and checked continuity from power cord though power switch all good. Contacting Shopsmith today. I hope I get better attention although mine was the do it yourself kit but it has been working for for the last three months.
No power to MarkV w PP Upgrade
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: No power to MarkV w PP Upgrade
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
kd6vpe
- Platinum Member
- Posts: 585
- Joined: Mon Jun 11, 2007 8:53 pm
- Location: Owasso, Oklahoma
- Contact:
Re: No power to MarkV w PP Upgrade
Oops sorry,
Did not mean to do a wrong thing. I have my return label comming from Shopsmith today, and they want the power supply and control display sent in for repair. Did not mean to do anything wrong was just curious but now I know what they wanted.
Thank you have a wonderful day
Did not mean to do a wrong thing. I have my return label comming from Shopsmith today, and they want the power supply and control display sent in for repair. Did not mean to do anything wrong was just curious but now I know what they wanted.
Thank you have a wonderful day
-
fredsheldon
- Platinum Member
- Posts: 1175
- Joined: Tue Jan 17, 2012 1:31 pm
- Location: The Woodlands, Texas
Re: No power to MarkV w PP Upgrade
My PowerPro bit the dust a couple years ago. I installed it in 2010 and have turned almost a hundred bowls since. It just stopped in the middle of a bandsaw operation. There is a flicker of the backlight every 3 seconds or so, nothing else. No messages of any kind. I have taken it all apart looking for obvious possible issues like loose connections. I removed the flywheel off the motor to check the speed sensor and blow out the dust. Nothing worked so I sent the control panel and power supply to the mother ship about a month ago but haven't heard anything back yet. I'm willing to spend the $500 for a new power supply if that's the issue. I suspect service is very busy, especially if these units are beginning to fail. I had a second backup unit available which I reinstalled after having a reverse modification made to the motor. I've been using this stock setup for several years now and it serves my needs.
My concern is that SS may not be able to survive too many failures of the PP without a long term warranty to cover the cost of repairs or replacement. We have come to expect these great machines to perform without any issues for many years. I would recommend anybody thinking about acquiring the PP to have a used backup unit on hand in the event it will be needed, since it may be months before you get any repairs/replacements on the PP.
Fred Sheldon
My concern is that SS may not be able to survive too many failures of the PP without a long term warranty to cover the cost of repairs or replacement. We have come to expect these great machines to perform without any issues for many years. I would recommend anybody thinking about acquiring the PP to have a used backup unit on hand in the event it will be needed, since it may be months before you get any repairs/replacements on the PP.
Fred Sheldon