Drilling Jig
Moderator: admin
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Drilling Jig
The Shopsmith makes it too easy! I needed neatly spaced holes drilled in a strip of wood so I can use dowels to space my lathe chisels in the new rack I am building (my fourth redesign in about as many years). Used a T nut and some scrap wood. Quick and dirty, but worked great! No measuring, no center lines to scribe.
- Attachments
-
- Drilling jig.jpg (201.04 KiB) Viewed 15534 times
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Drilling Jig
And no, I don't have a cat. The bucket came with the used Shopsmith 500, now 520 Shortened... 
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Re: Drilling Jig
Nice, simple jig!
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
-
BuckeyeDennis
- Platinum Member
- Posts: 3815
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Drilling Jig
Very clever, Chris! I had to study it a bit before I could figure out how it worked. I think I may have an application for a jig like that myself.
I gather that you can change the hole spacing by simply sliding the jig on the fence ... do you have any particular system for setting the desired hole spacing?
I gather that you can change the hole spacing by simply sliding the jig on the fence ... do you have any particular system for setting the desired hole spacing?
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Drilling Jig
Yes, slide on the fence. If you have a wider board, d rill a new hole. Easy peasy! I did not have any system for the spacing, I just drilled a few test holes and when it looked right I went with it.
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
ChrisNeilan
- Platinum Member
- Posts: 1463
- Joined: Sun Oct 27, 2013 5:30 pm
- Location: Waterford, Connecticut
- Contact:
Re: Drilling Jig
In case you were wondering, this is the lathe chisel rack. Room for 22 lathe tools and I can fit my 8 (yes 8) chucks in the bottom section. I may or may not add doors... So far built out of scrap wood.
- Attachments
-
- 7CC08C8B-FF97-4DC4-9675-914AD5E65D84.jpeg (139.93 KiB) Viewed 15490 times
Chris Neilan
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
Shopsmith Mark 7, Shopsmith Mark V 1982, shortened, Shopsmith 10 ER; Craftsman table saw (1964); Powermatic 3520B lathe
-
WileyCoyote
- Gold Member
- Posts: 182
- Joined: Thu Mar 29, 2018 6:52 pm
- Location: New Carlilse, Oh
Re: Drilling Jig
Nice job. Your scrap wood looks a lot nicer than my scrap wood.
-
mountainbreeze
- Platinum Member
- Posts: 511
- Joined: Sun Jan 30, 2011 9:58 pm
- Location: Ocala, FL
Re: Drilling Jig
Cleaver jig! Would this be an good way to drill shelf pin holes?
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Drilling Jig
mountainbreeze wrote:Cleaver jig! Would this be an good way to drill shelf pin holes?
I think so. However, tolerances between the two adjacent rows would be more critical(rocking shelve).
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
BuckeyeDennis
- Platinum Member
- Posts: 3815
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Drilling Jig
I'd use this jig to make a full-length drilling template, and then use that template to drill all the shelf supports. That would ensure that all supports for a given shelf are at the exact same height. Especially if you're willing to invest ten bucks in a drill bushing.JPG wrote:mountainbreeze wrote:Cleaver jig! Would this be an good way to drill shelf pin holes?
I think so. However, tolerances between the two adjacent rows would be more critical(rocking shelve).