I have two used Power Stations. Both have the same problem when the carriage return is moved as close as possible to the motor in order to connect the Band Saw. The carriage lock doesn't work when moved to the right. It does lock when it's further back on the stand. As it slides along there is a grove and he metal is lipped but as it moves forward to the motor that lip is no longer. The latch won't lock because there isn't enough metal to press against, I believe. Is there a fix from Shopsmith or does someone in this forum have an answer?
Thank You,
Mike
Power Station Carraige Lock
Moderator: admin
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Power Station Carraige Lock
Where is the hub on the Band saw shaft?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
chapmanruss
- Platinum Member
- Posts: 4544
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: Power Station Carraige Lock
Mike,
I'll check my Power Stations tomorrow with my Band Saws to see if I can see what problem there may be and get back to you. Happy Easter.
I'll check my Power Stations tomorrow with my Band Saws to see if I can see what problem there may be and get back to you. Happy Easter.
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Power Station Carraige Lock
Assuming this is a legitimate question:
The carriage moves much further than is required to mount the bandsaw.
The carriage should NOT be off the 'lip' when mounted.
So I have to also assume the coupler is not OEM or perhaps not even there?
A reply from OP will help further discussion or lack thereof will stop it altogether..
The carriage moves much further than is required to mount the bandsaw.
The carriage should NOT be off the 'lip' when mounted.
So I have to also assume the coupler is not OEM or perhaps not even there?
A reply from OP will help further discussion or lack thereof will stop it altogether..
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
chapmanruss
- Platinum Member
- Posts: 4544
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: Power Station Carraige Lock
As I said I would I checked this out. I have 2 Power Stations and currently 3 Band Saws. Using an OEM Coupler I cannot repeat the problem Mike is having. I believe JPG's assumptions are correct. Below is how it should look when mounted correctly. This is a picture I borrowed and not my tools. Do note that the carriage is not all the way to the end of the center slot closest to the Headstock.
- Band Saw on Power Station.jpg (187.77 KiB) Viewed 4864 times
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.