Deck work

This is a forum for intermediate to advanced woodworkers. Show off your projects or share your ideas.

Moderator: admin

Post Reply
bainin
Platinum Member
Posts: 569
Joined: Mon Apr 22, 2019 11:09 pm
Location: NC

Deck work

Post by bainin »

Having my Powerpro out for what seems like a long repair, I've been putting the time to some use trying to square away this deck/3 season room. Turns out it is a lot of stuff I wanted to do.

Here is where the contractor left off-on my request-they didnt complete the lattice work as I figured I could complete myself-given an example (which I had them do).
porch-start.jpg
porch-start.jpg (184.27 KiB) Viewed 7838 times
First-after a good rain, I realized the open section of deck was dumping a lot of water underneath next to the house and on my ac units :/ So I found a nice/reasonably cheap water capture idea online and followed it. I attached some wavy plastic panels to support and graded it properly to an underdeck gutter, finally connecting into the existing downspout.

If you look close-you can see that pressure treated 2x4x10 is suspended in place by some twine-have to get inventive when working alone :)
water1.jpg
water1.jpg (166.07 KiB) Viewed 7838 times
water2.jpg
water2.jpg (115.25 KiB) Viewed 7838 times
water3.jpg
water3.jpg (95.44 KiB) Viewed 7838 times
Its been dry as a bone underneath since the install was completed.
With that done-I went on to finish the cross-hatch work.
crosshatch1.jpg
crosshatch1.jpg (189.13 KiB) Viewed 7838 times
crosshatch2.jpg
crosshatch2.jpg (162.24 KiB) Viewed 7838 times
And finally-working on staining and finishing the floor inside.
floor0.jpg
floor0.jpg (64.63 KiB) Viewed 7838 times
floor1.jpg
floor1.jpg (121.9 KiB) Viewed 7838 times
floor3.jpg
floor3.jpg (82.4 KiB) Viewed 7838 times
I just did a 220 grit pass over the first layer of poly and will finish up with a 2nd poly and sand today (hopefully).

At this point, I have to switch to geology and build a stone walkway from the bottom of the stairs around to my shop door :) Trying to go fast as I am running out of semi-cool days here...starting to see 80+F by the end of the week.

hope you are all staying safe out there !

b
Hobbyman2
Platinum Member
Posts: 2673
Joined: Wed Feb 01, 2017 12:52 am
Location: Ohio

Re: Deck work

Post by Hobbyman2 »

nice job!!
Hobbyman2 Favorite Quote: "If a man does his best, what else is there?"
- General George S. Patton (1885-1945)
User avatar
BuckeyeDennis
Platinum Member
Posts: 3815
Joined: Tue Jul 24, 2012 10:03 pm
Location: Central Ohio

Re: Deck work

Post by BuckeyeDennis »

That is truly striking. My wife has been wanting to convert our backyard deck into a screened porch for a long long time. Something to do with mosquito bites ... 🤔
bainin
Platinum Member
Posts: 569
Joined: Mon Apr 22, 2019 11:09 pm
Location: NC

Re: Deck work

Post by bainin »

Almost done with the paver walkway now.

We've gotten pretty far along this spring with the lockdown. Still waiting my powerpro to return from repair.

almostdone.jpg
almostdone.jpg (190.7 KiB) Viewed 6945 times

b
RFGuy
Platinum Member
Posts: 3116
Joined: Mon Dec 31, 2018 8:05 am
Location: a suburb of PHX, AZ

Re: Deck work

Post by RFGuy »

Looks great! For the deck exterior will you paint it or keep it natural?
📶RF Guy

Mark V 520 (Bought New '98) | 4" jointer | 6" beltsander | 12" planer | bandsaw | router table | speed reducer | univ. tool rest
Porter Cable 12" Compound Miter Saw | Rikon 8" Low Speed Bench Grinder w/CBN wheels | Jessem Clear-Cut TS™ Stock Guides
Festool (Emerald): DF 500 Q | RO 150 FEQ | OF 1400 EQ | TS 55 REQ | CT 26 E
DC3300 | Shopvac w/ClearVue CV06 Mini Cyclone | JDS AirTech 2000 | Sundstrom PAPR | Dylos DC1100 Pro particulate monitor
bainin
Platinum Member
Posts: 569
Joined: Mon Apr 22, 2019 11:09 pm
Location: NC

Re: Deck work

Post by bainin »

Its all pressure treated-I don't mind the natural color..but the wife is getting quotes for staining :)

Will staining preserve pressure treated lumber better than no stain ? That would decide it for me rather than curb appeal.

b
RFGuy
Platinum Member
Posts: 3116
Joined: Mon Dec 31, 2018 8:05 am
Location: a suburb of PHX, AZ

Re: Deck work

Post by RFGuy »

I am no expert on finishing, but I think staining or applying a water sealer will prolong the life of it. Also, it serves to reduce the amount of surface cracks and checking you might have. I know some people annually apply water sealer to their pressure treated decks. How much this is really needed versus not needed though, I couldn't say. Pressure treated should last a long time with or without finish, I would think.

Here in AZ the sun is brutal on anything outside. The few wooden outdoor projects that I have done quickly develop check cracks and eventually the finish flakes off here. Items that are in full sun here probably need a re-application of finish every 3-6 months to be useful. I am still in search of a longer lasting wood finish for the AZ heat. I know paint would be better here, but I prefer a more natural wood finish.
📶RF Guy

Mark V 520 (Bought New '98) | 4" jointer | 6" beltsander | 12" planer | bandsaw | router table | speed reducer | univ. tool rest
Porter Cable 12" Compound Miter Saw | Rikon 8" Low Speed Bench Grinder w/CBN wheels | Jessem Clear-Cut TS™ Stock Guides
Festool (Emerald): DF 500 Q | RO 150 FEQ | OF 1400 EQ | TS 55 REQ | CT 26 E
DC3300 | Shopvac w/ClearVue CV06 Mini Cyclone | JDS AirTech 2000 | Sundstrom PAPR | Dylos DC1100 Pro particulate monitor
Post Reply