JPG wrote: Tue Dec 08, 2020 9:01 pm
I have to check this, but IIRC the tool rest arm bore is 3/4". The tail stock adapter begins life as 3/4" round bar stock and the 5/8 chuck end and the tailstock #2 mt are machined from it. A 3/4 " shoulder remains.
Yes, that appears to be the case from Ed's last picture. However, is that shoulder long enough for the arm set screw to engage it? Apparently it is since he did it.
I will have to check tomorrow.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
If you let the the tail stock adapter drop far enough, the set screw will secure it. The 5/8 portion will be slightly shorter proud of the arm, but there is enough to secure the faceplate.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
It is a bit of a balancing act but it works. The trick is to get the arm set screw to catch the shaft and the face place set screw to get enough grip on the flat.
The idea is in one of the older the PTWFE, they don't use the face plate but simply clamp to the arm. When I have time I will try and find it and give you a page reference and edition.....
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
[Note: Based on feedback, this post was very confusing, so with JPG"s wise suggestion, I edited the original wording of this post.]
Ah - Now I understand. Was easy to take 3/4 threaded rod and grind one end down to 5/8. Made an adapter to connect a face plate to the tool rest arm SIMILAR to Reible using a tailstock chuck adapter for the same purpose. i.e. the low $$$ approach! Easy peasy. Thanks all.
3/4 threaded rod ground to 5/8 at one end
3_4 thread to 5_8.jpg (139.17 KiB) Viewed 2584 times
perfect fit into faceplate
fit to faceplate.jpg (176.85 KiB) Viewed 2584 times
hal
Last edited by hfmann on Thu Dec 10, 2020 9:26 am, edited 2 times in total.
hfmann wrote: Wed Dec 09, 2020 3:32 pm
Ah - Now I understand. Was easy to take 3/4 threaded rod and grind one end down to 5/8. Easy peasy. Thanks all.
3_4 thread to 5_8.jpg
fit to faceplate.jpg
hal
WTH??
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
hfmann wrote: Wed Dec 09, 2020 8:32 pm
It's how I made my own tailstock adapter to work for Ed Reible's way to mount a gouge to the tool rest arm. Does that make sense now?
hal
Tail stock adapter??? No it does not make any sense.
John & Mary Burger
Eagle's Lair Woodshop
Hooper, UT
hfmann wrote: Wed Dec 09, 2020 8:32 pm
It's how I made my own tailstock adapter to work for Ed Reible's way to mount a gouge to the tool rest arm. Does that make sense now?
hal
Tail stock adapter??? No it does not make any sense.
Change the wording - Made an adapter to connect a face plate to the tool rest arm SIMILAR to Reible using a tailstock chuck adapter for the same purpose. i.e. the low $$$ approach!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
hfmann wrote: Wed Dec 09, 2020 8:32 pm
It's how I made my own tailstock adapter to work for Ed Reible's way to mount a gouge to the tool rest arm. Does that make sense now?
hal
Tail stock adapter??? No it does not make any sense.
Change the wording - Made an adapter to connect a face plate to the tool rest arm SIMILAR to Reible using a tailstock chuck adapter for the same purpose. i.e. the low $$$ approach!
