They are bare metal and will never be seen again.
- Jointer1.jpg (164.43 KiB) Viewed 1750 times
- jointer2.jpg (229.13 KiB) Viewed 1750 times
1982 Jointer Reassembly
Moderator: admin
1982 Jointer Reassembly
I have completely disassembled my 1982 jointer and painted. Now I need to reassemble. What lube/coating should I use for the slides?
They are bare metal and will never be seen again.
They are bare metal and will never be seen again.
1982 Mark V 500 w/2 bandsaws(cast iron and aluminum table), power station, belt sander, jointer, jigsaw and lathe duplicator.
-
dusty
- Platinum Member
- Posts: 21481
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: 1982 Jointer Reassembly
no oil/grease. a good coat of Johnsons Paste Wax would be my choice.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: 1982 Jointer Reassembly
With some powered grapite sprinkled on top of the still 'wet' wax.
Do NOT buff.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: 1982 Jointer Reassembly
Is that a special JPG trick? Never thought of doing both. Does it make a big difference? Thanks.
RF GuyMark V 520 (Bought New '98) | 4" jointer | 6" beltsander | 12" planer | bandsaw | router table | speed reducer | univ. tool rest
Porter Cable 12" Compound Miter Saw | Rikon 8" Low Speed Bench Grinder w/CBN wheels | Jessem Clear-Cut TS™ Stock Guides
Festool (Emerald): DF 500 Q | RO 150 FEQ | OF 1400 EQ | TS 55 REQ | CT 26 E
DC3300 | Shopvac w/ClearVue CV06 Mini Cyclone | JDS AirTech 2000 | Sundstrom PAPR | Dylos DC1100 Pro particulate monitor
-
dusty
- Platinum Member
- Posts: 21481
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: 1982 Jointer Reassembly
I'm not inclined to do both. I fear that the combination would tend to form a paste.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
chapmanruss
- Platinum Member
- Posts: 4232
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: 1982 Jointer Reassembly
First make sure all paint is removed from the contact points. Especially in the tongue and groove side. You want to have smooth bare metal to bare metal. Use paste wax for protection and lubrication. If later it doesn't slide as well you can take it apart again and re-wax. It is only the one bolt that holds them together so not a difficult job. I haven't tried JPG's addition of graphite but you could try it if you wish.
Once you have it reassembled check the tables to make sure they are parallel by adjusting the cut to 0 and using a long metal straight edge across the infeed and outfeed tables. Once it is parallel you can set your depth of cut indicator to 0.
Once you have it reassembled check the tables to make sure they are parallel by adjusting the cut to 0 and using a long metal straight edge across the infeed and outfeed tables. Once it is parallel you can set your depth of cut indicator to 0.
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Re: 1982 Jointer Reassembly
I too am reassembling my jointer after refurbishing it. I need to know where the pin in the attached photo goes? Thanks.
- Attachments
-
- 20210309_125407.jpg (221.42 KiB) Viewed 1604 times
-
- 20210309_153332.jpg (325.38 KiB) Viewed 1604 times
-
chapmanruss
- Platinum Member
- Posts: 4232
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: 1982 Jointer Reassembly
Are you talking about the item circled in the picture below?
_
It looks like part of a paper clip. I don't know what it belongs to but is not from the Jointer. See the exploded parts drawing attached below. Although the drawing is for newer Jointers than yours made in 1980 most of the parts are the same. The main differences are the feather board blade guard, the other guards and the dust chute. These are available as upgrades from Shopsmith. It does show the old cutter head assembly like yours has.
_
Note for anyone else referencing this - the online parts diagram does not show the correct 5 hole wedges used in the new slightly larger diameter cutter head. The cutter head must be replaced as an assembly (except the blades) for the correct wedges and set screws. The blades are the same for all models.
_
- Jointer part - circle.jpg (99.71 KiB) Viewed 1565 times
_
Jointer Illustrated Exploded Parts Drawing 8 Oct 2017 extensively reworked by Everett L. Davis.pdf- (1.58 MiB) Downloaded 192 times
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's & 2 Power Stations
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored. Others to be restored.
Re: 1982 Jointer Reassembly
Might be a staple used in cheap furniture.
Ron Dyck
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,
==================================================================
10ER #23430, 10ER #84609, 10ER #94987,two SS A-34 jigsaws for 10ER.
1959 Mark 5 #356595 Greenie, SS Magna Jointer, SS planer, SS bandsaw, SS scroll saw (gray), DC3300,