Shorty Drill Press not perpendicular to floor, any ideas?

[dusty]

I am a believer even If I don't understand the images.

[dusty]

Yes the anglecube does something different - see the other thread.

It has some difference in display format but it works essentially the same.

Wixey showing rotation through 90 degrees to 91.3 degrees (1.3 degrees rotated past 90 degrees)

Mike 4.jpg (139.92 KiB) Viewed 780 times

[JPG]

The wixey says the wixey has been rotated 91.3 degrees.

The 90 degree point(tube vertical) would indicate 90.0egrees.

The wixey rotated CW 1.3 degrees past that.

WHY?

Because the tube is not quite vertical(UNDER rotated).


I think our earlier discussions re over rotation has been baloney.

over

[algale]

The wixey says the wixey has been rotated 91.3 degrees.

The 90 degree point(tube vertical) would indicate 90.0egrees.

The wixey rotated CW 1.3 degrees past that.

WHY?

Because the tube is not quite vertical(UNDER rotated).


I think our earlier discussions re over rotation has been baloney.

over

That makes no sense to me. If it was under rotated wouldn't the Wixey read less than 90?

[Majones1]

That makes no sense to me. If it was under rotated wouldn't the Wixey read less than 90?

No, you have to go back to the earlier photo where this one came from, and see the previous photo that showed it at zero. There was a mistake in how the Wixey was placed. In the previous photo it was attached to the top of the bench tube, and then rather than rotating the Wixey counter-clockwise, where it would be on the left side of the way tube, it was rotated clockwise and attached to the right side of the way tube. So it’s upside down and showing over rotation rather than the correct under rotation. That was where a major confusion was introduced into the discussion.

[Majones1]

Oh, and I think that photo ended up sideways too? Making the confusion even more confusing.

[JPG]

The wixey says the wixey has been rotated 91.3 degrees.

The 90 degree point(tube vertical) would indicate 90.0egrees.

The wixey rotated CW 1.3 degrees past that.

WHY?

Because the tube is not quite vertical(UNDER rotated).


I think our earlier discussions re over rotation has been baloney.

over

That makes no sense to me. If it was under rotated wouldn't the Wixey read less than 90?

This post is relative to the two pix posted by Dusty.

The 91.3° pix shows the wixey rotated CW 91.3° from level(horizontal).

The wixey is over 90 rotated to attach to the way tube which is 'under' rotated by 1.3°.

[Majones1]

Ed- it’s bottomed out and still leans towards operator-
Here are a couple pics with zero on bench tubes

These are the two photos that I was talking about. If you look closely you will see the second photo is actually sideways, and I believe this is the photo that Dusty re-posted above, after correcting the rotation. Also, in that second photo, you can see that the Wixey was rotated incorrectly from zero, further confusing the issue.

Or am I seeing something wrong?

[JPG]

Make me a believer! Post a picture of a Wixey that was zeroed on the horizontal and then rotated to 135 degrees.

Reference.JPG


Ref 45.JPG


Ref 135.JPG

I'll have to go look at your other thread. I take it that the angle cube does something else.

- David

DLB's pix may show this more clearly.

The first pix is wixey 'level'. reads 0.00 tubes __

The second pix is the same as waytubes rotated CCW 45° past 90. reads 45.0° tubes \__ wixey rotated CW 45°

The third pix is the same as waytubes rotated CCW 45° short of 90. reads 135° tubes /__ wixey rotated CW 135°

[JPG]

Ed- it’s bottomed out and still leans towards operator-
Here are a couple pics with zero on bench tubes

These are the two photos that I was talking about. If you look closely you will see the second photo is actually sideways, and I believe this is the photo that Dusty re-posted above, after correcting the rotation. Also, in that second photo, you can see that the Wixey was rotated incorrectly from zero, further confusing the issue.

Or am I seeing something wrong?

Those pix are the original.

Current 'discussion' is re DLB's pix.

Regardless both sets of pix show the action of the wixey. Understanding that is the obstacle to complete understanding of just what IS being demonstrated by a pix of a wixey attached to a way tube.