No, but I am smoking a pork butt this weekend?
Quill difficult to advance
Moderator: admin
Re: Quill difficult to advance
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Quill difficult to advance
The 73's are what prompted the question.
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
Re: Quill difficult to advance
I think JPG was suggesting you might be a ham radio operator. I had to go luck up what "73" means in code for a ham operator to understand. Perhaps Wes was born in 1973? I never got into ham radio...I know strange considering I spent my career specializing in RF/Microwave communication (hence my screen name here). I do have fond memories of shopping ham radio swap meets back when I was a youngling though. In the pre-online era, they were a good place to shop for computer parts, ham radio gear and generally any electronic parts, etc. I bought my VARIAC® from one of these swap meets. Hope your pork butt turned out well. I am also a fellow BBQ guy, but too hot in Phoenix area to smoke anything in the summer time unfortunately. Welcome to the forum!
RF GuyMark V 520 (Bought New '98) | 4" jointer | 6" beltsander | 12" planer | bandsaw | router table | speed reducer | univ. tool rest
Porter Cable 12" Compound Miter Saw | Rikon 8" Low Speed Bench Grinder w/CBN wheels | Jessem Clear-Cut TS™ Stock Guides
Festool (Emerald): DF 500 Q | RO 150 FEQ | OF 1400 EQ | TS 55 REQ | CT 26 E
DC3300 | Shopvac w/ClearVue CV06 Mini Cyclone | JDS AirTech 2000 | Sundstrom PAPR | Dylos DC1100 Pro particulate monitor
Re: Quill difficult to advance
Ahh, that makes sense! Not a ham radio guy, but have friends that used to love that.
To follow up the original question, I disassembled the quill and pinion shaft yesterday. Everything looks good, spring intact. Lots of friction in spring housing, took a small file and smoothed the edges of the housing where it rotates then spray lubed with some dry lubricant, helped. I did realize I am missing the domed washer that goes on the pinion shaft inside the headstock, so I will order that from the mothership.
Does anyone have a part number for that domed washer? It is part number 53 on the exploded parts diagram.
-Wes
To follow up the original question, I disassembled the quill and pinion shaft yesterday. Everything looks good, spring intact. Lots of friction in spring housing, took a small file and smoothed the edges of the housing where it rotates then spray lubed with some dry lubricant, helped. I did realize I am missing the domed washer that goes on the pinion shaft inside the headstock, so I will order that from the mothership.
Does anyone have a part number for that domed washer? It is part number 53 on the exploded parts diagram.
-Wes
-
chapmanruss
- Platinum Member
- Posts: 4547
- Joined: Tue Aug 26, 2014 8:16 pm
- Location: near Portland, Oregon
Re: Quill difficult to advance
The Washer reference number 53 on the parts diagram is part number 501317 Price $6.95 described as Spherical Washer (.812ID 1.43). You can find it at the link below.
https://www.shopsmith.com/product-page/washer-10
https://www.shopsmith.com/product-page/washer-10
Russ
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.
Mark V completely upgraded to Mark 7
Mark V 520
All SPT's, 2 Power Stations & Crafter's Station
Model 10ER S/N R64000 first one I restored on bench w/ metal ends & retractable casters.
Has Speed Changer, 4E Jointer, Jig Saw with lamp, a complete set of original accessories & much more.
Model 10E's S/N's 1076 & 1077 oldest ones I have restored. Mark 2 S/N 85959 restored.