Proud new owner

dlbristol · Post by **dlbristol** » Thu Jun 25, 2009 9:47 am

Welcome to the forum. As you have seen, there is a great deal of help to be had here. I can't offer much help, but these guys know the machines and wood working. You have far more skill than I had to start, so you will be fine. I can tell you that I have never been led astray. One thing I might add is a quote from some one here on the forum. : "Learn to think Shopsmith", meaning look for ways to use the uniqueness of the machines. Good luck.

hobbydad · Post by **hobbydad** » Fri Jun 26, 2009 2:35 pm

When I first looked over the machine, the quill would get stuck if extended over halfway. I would have to nudge the lever a few times to get it to retract. The spring was also noisy toward the end of its travel.

I disassembled pretty much everything in the headstock and found dust packed into the groove on the top of the quill and in the quill spring. I cleaned everything out and started to reassemble the quill return. I preloaded the spring with two full turns, and I'm hearing noise from the spring after the first turn. Is this normal? I need to decide whether or not to put the spring housing on my shopping list.

I'm glad I took the spring housing off the shaft for cleaning, but it was kind of a pain to put back on. I probably would have had a mental breakdown if not for the help from previous posts on the subject.

Loren

billmayo · Post by **billmayo** » Fri Jun 26, 2009 4:27 pm

hobbydad wrote:When I first looked over the machine, the quill would get stuck if extended over halfway. I would have to nudge the lever a few times to get it to retract. The spring was also noisy toward the end of its travel.

I disassembled pretty much everything in the headstock and found dust packed into the groove on the top of the quill and in the quill spring. I cleaned everything out and started to reassemble the quill return. I preloaded the spring with two full turns, and I'm hearing noise from the spring after the first turn. Is this normal? I need to decide whether or not to put the spring housing on my shopping list.

Loren

You only need another spring housing, spring or quill feed pinion if any of them are broken. Quill Feed Spring noise is common problem. Most people live with it. I move the snap ring #38 out to the threads on the quill feed pinion and pull the spring housing to the snap ring. I spray a dry lube into the open end of the spring housing to coat the spring. Reset the snap ring and spring noise is no more. I do this to all the Quill Feed Assemblies.

hobbydad · Post by **hobbydad** » Fri Jun 26, 2009 4:46 pm

Bill,

Thanks for the tip. Comparing the condition of my wallet to the condition of the spring, I will probably hold off getting a new one.

Loren

joedw00 · Post by **joedw00** » Fri Jun 26, 2009 7:50 pm

Loren
Welcome to the forum!!:)

hobbydad · Post by **hobbydad** » Sat Jun 27, 2009 6:50 pm

Today I placed my order for replacement parts. I ordered a new speed control assembly, control sheave, drive belt, and some hardware it was missing. I also had time to perform a full inventory of my purchase. Here is what my ~$500 investment got me:

1979 SS Mark V - original table and fence, poly v-belt
Original manuals & receipts
1 copy of PTWFE

Jointer w/ extra knives
Band saw - w/ separate mount & motor (not SS-made) band saw needs some TLC
Jig saw w/ extra blades
2 power couplers
Outfeed table
Some dust collection parts
2 saw blades w/ arbors
Miter gauge, fence straddler, featherboard, stop rod
Table inserts (std, dado, drum)
SS dado blades
Craftsman shaper set
Drill chuck w/ 2 keys
Router bit chuck & SS router bits (1/4", 3/8", 1/2", 9/16")
Chuck/adaptor(?) - from SS spindle to 1/4"
Sanding wheels, polishing wheel
Sanding disc
Sanding drum
Shaper fence (missing 1 adjustment knob)
Cut off wheel w/ arbor
2 grinding wheels w/ arbors & extra wheel
Lathe tailstock, tool rest (w/ extra, curved tool rest - pic attached), assorted dead centers
8 lathe chisels
and 1 small table with a miter slot that I cannot identify. pic attached.

Does it seem like I am missing anything critical? I feel like I got a pretty good deal for what I paid. Sorry for the long post...

Loren

reible · Post by **reible** » Sat Jun 27, 2009 7:02 pm

Hi,

The small table is a Front Table Extension (505626) it gives you 7" more space by attaching to the front of the main table.

Ed

JPG · Post by **JPG** » Sun Jun 28, 2009 1:02 am

Extension tablle?? Or are you calling it an outfeed table???

charlese · Post by **charlese** » Sun Jun 28, 2009 2:11 am

JPG40504 wrote:Extension tablle?? Or are you calling it an outfeed table???

It is an INFEED table. Formally called (or named) " MARK V 500 Front Table Extension" http://www.shopsmith.com/ownersite/item ... =Find+Item

555306 is for outfeed support on a 500.

hobbydad · Post by **hobbydad** » Mon Jun 29, 2009 11:53 am

Thanks for the help on that extension table. It looks like it gives you more room for using the miter gauge on wider pieces. That is something I could use on my 10" Craftsman band saw, which I guess I will be using for longer than I hoped... I placed my parts order over the weekend and called for parts availability today. The speed control assy and control sheave assy are both on backorder

Loren

Shopsmith Forums

Proud new owner

Welcome

Quill spring question

Quill Return Spring

Inventory

Bummed