Any Mark 2 owners here. I need some instruction

mickyd · Post by **mickyd** » Sat Jan 23, 2010 10:31 am

lazerrus wrote:Here are some pics. Sorry for the quality i used my phone. It has everything for it also. The saw table, 9 inch sanding disc etc.

Now ain't she adorable!!!! Thanks for posting the pics. She's looks fantastic. Looks like I'll have to add one of those to my collection in 2011 (adding a Mark VII is my 2010 goal).

JPG · Post by **JPG** » Sat Jan 23, 2010 11:08 am

mickyd wrote:Now ain't she adorable!!!! Thanks for posting the pics. She's looks fantastic. Looks like I'll have to add one of those to my collection in 2011 (adding a Mark VII is my 2010 goal).

And in 2012? Go find the 'missing' Mark 1(there were 2 made, one is accounted for).

wlhayesmfs · Post by **wlhayesmfs** » Sat Jan 23, 2010 11:21 am

I have seen two but was not able to obtain one, One was sold and one wanted $300 so I passed. I have the owners manual for one I picked up in some trading for some paperwork. Just waiting to fine one the right price just to have one. Not sure how much I would use it. Might work for a sanding station and work

wlhayesmfs · Post by **wlhayesmfs** » Sat Jan 23, 2010 11:22 am

JPG40504 wrote:And in 2012? Go find the 'missing' Mark 1(there were 2 made, one is accounted for).

Never knew about any Mark 1 have any pictures or data you can post?
thanks

iclark · Post by **iclark** » Sat Jan 23, 2010 7:40 pm

wlhayesmfs wrote:Never knew about any Mark 1 have any pictures or data you can post?
thanks

check out this site:
http://shopsmith-tool-hunter.blogspot.com/
there is info about the manual near the top.
a photo of a Mark I is about 2/3 down the page (today).
I believe that the page owner is a member here.

Ivan

lazerrus · Post by **lazerrus** » Mon Jan 25, 2010 8:28 am

JPG40504 wrote:What does the crank on the front of the headstock do?

Sort of a cross between a 10 e/r and a mark 5/V! I gotta wonder if a mark 5/V tailstock would fit/work(I think it would). That table has got to be a PITA!

Hi guys sorry for the delay been busy. The crank on the front is the belt tensioner by raising and lowering the motor. The pulleys are set up as I bought it so I don't know if it is right or not. Too change the speed I just loosen the top pully and slide it over. The extension I built is made of 1 1/2 inch laminated particle wood. Very strong and does the job just fine. I had no idea these were that rare. She runs like a champ. It came with everything for it also. Saw table. Disc Sander 9 inch. Spur drive. Dead center etc etc. I only paid $75 for the whole thing and im into about 4 hours of tune up, paint, polish etc. So not bad I'd say

lazerrus · Post by **lazerrus** » Mon Jan 25, 2010 8:55 am

If interested here are some before pics the day I brought it home.

robinson46176 · Post by **robinson46176** » Mon Jan 25, 2010 9:14 am

OK, now I am more confused...

It appears to have pivot ends on both ends????
Did it come with the main table? And saw arbor etc?
Will it tip up to drill press mode?
These are the first real good pictures I have seen of one of these and they just raise more questions.

Does it have the high speed jointer drive shaft between the motor and the upper shaft?
That caster set is probably worth about what you paid for the whole thing. I was a little surprised to see a set on a Mark II

lazerrus · Post by **lazerrus** » Mon Jan 25, 2010 12:35 pm

Yes it does I will post more pics for you guys in just a few.

lazerrus · Post by **lazerrus** » Mon Jan 25, 2010 12:52 pm

I actually have a buffing wheel on it right now but you'll get the idea. I also but the table on backwards for the photo but once again you get the idea.