robedney wrote:What's an SPT?
Special Purpose Tool.
trying to get motor turning
Moderator: admin
Special Purpose Tool.
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
a.k.a. bandsaw,jointer,belt sander,jigsaw,stripsander,scrollsaw...robedney wrote:What's an SPT?
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
-
dusty
- Platinum Member
- Posts: 21481
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Man-o-man is it ever good to hear from you again. I had thought that maybe you had completely given up on us now that you are no longer traveling.ricknwood wrote:If you have a 15 amp breaker and the 12" sanding disc attached, you must have the headstock speed down LOW or the situation you described would happen
We could sure us your input now and then. I pull the DVD out probably once a month minimum just to recheck what you had said about one thing or another.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
-
vanmeter2r
- Gold Member
- Posts: 33
- Joined: Fri Apr 23, 2010 11:45 pm
Dusty;
I'm active duty and got hurt in Afghanistan (non-combat related) and ended up being medivac home then went through back surgery (went through front and back). I'm on conversant leave right now and doing MUCH better. I'm taking things slow and hoping I don't get booted because I'm non world wide deployable right now. I think in about three months, i should be back to normal. As far as my shopsmith, I took some pictures and resizing them now to upload to the sight. My hope, if someone has any ideas once I upload the picture, they can help me by letting me know how I could have improved or let me know what was good.
I'm active duty and got hurt in Afghanistan (non-combat related) and ended up being medivac home then went through back surgery (went through front and back). I'm on conversant leave right now and doing MUCH better. I'm taking things slow and hoping I don't get booted because I'm non world wide deployable right now. I think in about three months, i should be back to normal. As far as my shopsmith, I took some pictures and resizing them now to upload to the sight. My hope, if someone has any ideas once I upload the picture, they can help me by letting me know how I could have improved or let me know what was good.
[quote="vanmeter2r"]Hello all]
I'm glad to hear that you are doing better in recovery from your back surgery. It will be a slow go so do not rush it. I have a failing back but as of right now can not say I have been so diagnosed.
Regarding your Mark V motor problem, did you ever get it to operate normally under load? I do not believe that 110vac line lose is the problem but do check the power cord and make sure that the voltage does not drop when the motor is under load. A bad power cord or "about to fail" switch could do that.
I'm glad to hear that you are doing better in recovery from your back surgery. It will be a slow go so do not rush it. I have a failing back but as of right now can not say I have been so diagnosed.
Regarding your Mark V motor problem, did you ever get it to operate normally under load? I do not believe that 110vac line lose is the problem but do check the power cord and make sure that the voltage does not drop when the motor is under load. A bad power cord or "about to fail" switch could do that.
MarkFive510
-
kd6vpe
- Platinum Member
- Posts: 585
- Joined: Mon Jun 11, 2007 8:53 pm
- Location: Owasso, Oklahoma
- Contact:
Ricknwood,
Wow what a surprise. I sure hope all is well with you. Does this maybe mean you are back for awhile? Did you ever continue of your DVD series on cabinet making? You see we do remember you and Nick even though it has been awhile.
Wow what a surprise. I sure hope all is well with you. Does this maybe mean you are back for awhile? Did you ever continue of your DVD series on cabinet making? You see we do remember you and Nick even though it has been awhile.
SS 500 upgraded to 510; SS bandsaw; SS jointer
SS Oscillating Drum Sander; Universal Lathe Rest;
lathe duplicatior, shaper fence and shapers; SS Belt
Sander
Jim
www.youtube.com/kd6vpe
SS Oscillating Drum Sander; Universal Lathe Rest;
lathe duplicatior, shaper fence and shapers; SS Belt
Sander
Jim
www.youtube.com/kd6vpe
-
vanmeter2r
- Gold Member
- Posts: 33
- Joined: Fri Apr 23, 2010 11:45 pm
thanks everyone
Thank all of you for supporting your service members;There is a-lot of people (military and civilians)around the world, fighting for our freedom. I do hope I get another opportunity to deploy, but I am unsure since I have 6 disk fused. As far as the motor running, I took SDSMITH advise and turned the motor slowly to get the belts aligned and now everything works great.