judaspre1982 wrote:Yes, a heavy hand can strip even the lighter duty Tinnerman nuts. In my line of work , I see large heavy duty Tinnermans stripped on commercial air handler doors all the time. The ones that are stripped the most are the hex head screws. They get stripped by people putting them in with a cordless drill and not setting the clutch properly.
Dave
Since it takes no time to tighten the screws in the headstock with a screwdriver, stripping the Tinnermans shouldn't be a problem, plus they are easy to replace. I'd say that's an easy solution. So would using a standard pan head with nut and washer, at least temporarily. But those would definitely go clinking to the floor.
ddvann79 wrote:Since it takes no time to tighten the screws in the headstock with a screwdriver, stripping the Tinnermans shouldn't be a problem, plus they are easy to replace. I'd say that's an easy solution. So would using a standard pan head with nut and washer, at least temporarily. But those would definitely go clinking to the floor.
How does one access the nut inside the motor pan/belt cover when tightening???;)
I like the sheet metal 'fix' the best. There is no indented surface on the tapped headstock for the tinnerman clip. Keep in mind the 'tinnerman' screws are not a machine thread, but more like a course self threading screw.
JB Weld a nut on the inside of the headstock?????:rolleyes:
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
dusty wrote:Did the original question ever gets answered? I
It is too soon to get back on the original topic yet but I think it might have been.
My question about those screws is why when you drop one (and they do escape often) can they not just drop to the floor? Why do they ALWAYS have to roll under something else??? They will roll 10' if need be just to crawl into a bad spot to be found. An old speaker magnet on a stick can be your friend.
--
farmer
Francis Robinson
I did not equip with Shopsmiths in spite of the setups but because of them.
1 1988 - Mark V 510 (bought new), 4 Poly vee 1 1/8th HP Mark V's, Mark VII, 1 Mark V Mini, 1 Frankensmith, 1 10-ER, 1 Mark V Push-me-Pull-me Drillpress, SS bandsaw, belt sander, jointer, jigsaw, shaper attach, mortising attach, TS-3650 Rigid tablesaw, RAS, 6" long bed jointer, Foley/Belsaw Planer/molder/ripsaw, 1" sander, oscillating spindle/belt sander, Scroll saw, Woodmizer sawmill
dusty wrote:Did the original question ever gets answered? I
Post #3!!!!!!!!!!!:D
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
robinson46176 wrote:It is too soon to get back on the original topic yet ]An old speaker magnet on a stick can be your friend.[/B]
Like this?
[ATTACH]11980[/ATTACH]
Notice the 'length' is adjustable!:D
Attachments
parts retriever.jpg (33.38 KiB) Viewed 2019 times
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
but I think it might have been.
Yeah, I didn't really think that through, did I?