Painting question

Forum for Maintenance and Repair topics. Feel free to ask questions or contribute.

Moderator: admin

Post Reply
markap
Gold Member
Posts: 99
Joined: Wed Oct 15, 2008 1:44 pm
Location: Reston, VA

Painting question

Post by markap »

When you paint with the Rustoleum "hammered" finish, do you use the spray can or quart container and a gun? If the latter, do you use it straight from the can or do you thin it with acetone first? What do you use to clean your gun afterwards?
SS MV 520, bandsaw, jointer, planer, belt sander, mortise unit, biscut jointer, speed reducer, tool rest upgrade, sliding cross cut table, DC3300
User avatar
ddvann79
Gold Member
Posts: 403
Joined: Wed Oct 20, 2010 10:34 am
Location: Fort Worth, Texas

Post by ddvann79 »

markap wrote:When you paint with the Rustoleum "hammered" finish, do you use the spray can or quart container and a gun? If the latter, do you use it straight from the can or do you thin it with acetone first? What do you use to clean your gun afterwards?
Mark,

Most of us just use it straight from a spray can. Easy, simple, minimal clean up and good results.

Check out Mickyd's restoration thread. He has cataloged the posts on painting. I did something similar with mine.
Dalton
Fort Worth, Texas
1962 MK 5 #373733 Goldie
User avatar
holsgo
Platinum Member
Posts: 740
Joined: Sat Jul 04, 2009 9:48 pm
Location: Manassas, VA

Post by holsgo »

Just use the spray can. I spray and then clean my gun with mineral sprits for just about everything, including Rustoleum. That said, the spray cans deliver a fine coat. Remember, hammered doesn't have to be perfect, that's the point. It hides imperfections.
markap
Gold Member
Posts: 99
Joined: Wed Oct 15, 2008 1:44 pm
Location: Reston, VA

Post by markap »

I'm actually planning to paint a metal utility trailer which is fairly rusted at the moment. I think it will be a bit much for the spray can approach so I plan to use the quart can of Rustoleum and my HVLP spray gun - hence the question of to thin or not to thin.

Also using this as practice before spraying lacquer on a guitar I'm building.
SS MV 520, bandsaw, jointer, planer, belt sander, mortise unit, biscut jointer, speed reducer, tool rest upgrade, sliding cross cut table, DC3300
User avatar
SDSSmith
Platinum Member
Posts: 1940
Joined: Mon Dec 04, 2006 6:35 pm
Location: San Diego, CA

Post by SDSSmith »

markap wrote:I'm actually planning to paint a metal utility trailer which is fairly rusted at the moment. I think it will be a bit much for the spray can approach so I plan to use the quart can of Rustoleum and my HVLP spray gun - hence the question of to thin or not to thin.

Also using this as practice before spraying lacquer on a guitar I'm building.
I bought a quart of the Hammered Gray and sprayed it using a Critter siphon type setup. I did thin with Xylol (picked up at my local True Value). I was very pleased with the results. If you have alot to spray and don't mind a little clean up, then it is a cheaper alternative to the rattle cans.
Rob in San Diego
Email: SDSSmith51 AT gmail.com
markap
Gold Member
Posts: 99
Joined: Wed Oct 15, 2008 1:44 pm
Location: Reston, VA

Post by markap »

SDSSmith wrote:I bought a quart of the Hammered Gray and sprayed it using a Critter siphon type setup. I did thin with Xylol (picked up at my local True Value). I was very pleased with the results. If you have alot to spray and don't mind a little clean up, then it is a cheaper alternative to the rattle cans.
Great - thanks for responding. I'll look for the Xylol
SS MV 520, bandsaw, jointer, planer, belt sander, mortise unit, biscut jointer, speed reducer, tool rest upgrade, sliding cross cut table, DC3300
Post Reply