Thinking about getting this for heat
Moderator: admin
Re: Thinking about getting this for heat
That big buddy heater will not put out the heat you think it does. I have one for my fish house and it works but not great. If you are going to use or store it in a shop area where there is any dust in the air you will have problems keeping it going. Unless they changed the design there is a vent tube where the pilot is and it constanty get dut in it and the pilot goes out. The infra red that I have has no fan fan and it heat objects instead of the air then the heat comes off the objects to heat the room so they say
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Thinking about getting this for heat
I wood love to have one of those going in the garage just not practical for at moms.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: Thinking about getting this for heat
I have the Big Buddy that I used in my outside very drafty 12x16 shop with little insulation. On a day with little or no wind, it could raise the temperature about 20-25 degrees in an hour or so on high (both burners), then I would turn it to low or medium (one burner). I imagine it would do that if not better in a decently sealed garage even if no insulation. If you're going to use a propane tank, be sure to get the hose and regulator: https://smile.amazon.com/gp/product/B00 ... UTF8&psc=1. You'll probably also want the 6V adapter so you don't have to use batteries: https://smile.amazon.com/gp/product/B00 ... UTF8&psc=1.ERLover wrote:I decided to go with this one and get the AC fan adapter, and 20lb tank adapter, I liked its reviews, safety record and reputation.
http://www.farmandfleet.com/products/47 ... eater.html
I was looking at this for price but had bad reviews on Amazon and a few other shopping sites.
http://www.farmandfleet.com/products/83 ... eater.html
I will heat up the garage with the propane while having coffee and BSen with Dusty, then use a 1500 watt electric Milk House heater with a fan a thermostatic control to maintain at 60*, course that depends on the outside temp of the day!!! My knew adventure, I like ruffing it, I did not have to walk to school and back up hill both ways in below zero weather and 3ft of snow, BUT I had to deliver my paper route in it!!!!
http://www.farmandfleet.com/products/83 ... eater.html
Roy
Mark V/510, Mark V/500 with parts for 510 upgrade, bandsaw, jointer, belt sander, DC3300 w/1 micron bag
Sawstop 3HP 36" PCS w/router table insert
Home designed and built CNC router, another CNC router
desktop size, Avid 5x10 Pro CNC w/ATC, CNCed G0704 milling machine
Laser engraver
Way too much other stuff and not enough space
Mark V/510, Mark V/500 with parts for 510 upgrade, bandsaw, jointer, belt sander, DC3300 w/1 micron bag
Sawstop 3HP 36" PCS w/router table insert
Home designed and built CNC router, another CNC router
Laser engraver
Way too much other stuff and not enough space
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Thinking about getting this for heat
Roy, plan on getting that today, I am going to use a tank. Thanks for thetemp update, sounds like it will do the job. Garage is attached to the house and one other wall is insulated, 8ft ceiling, dry walled and insulated.
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
Re: Thinking about getting this for heat
Dennis, when I lived in Oklahoma, and had ER#1, I had something similar.
Except, it was a real kitchen wood-burning range.
Old fashioned, all Cast Iron, and did a GREAT job of heating
the garage.
I used dual-wall stove pipe, and made a horizontal section,
to go through the side wall. Pulled off the sheet-rock between 2
studs, as well as the exterior wall, and made a 16X16 hole in the
wall. Put a floor in it (wood, I think) and used sheet metal to re-cover
the hole, after the pipe went through. Filled up the cavity with
vermiculite, since it is light and fireproof.
Like most old wood-burning stoves, this one had a lever on it, to
direct the exhaust around the oven, before going up the pipe.
Yes, I did cook on it. (And, in the oven.)
steve
Except, it was a real kitchen wood-burning range.
Old fashioned, all Cast Iron, and did a GREAT job of heating
the garage.
I used dual-wall stove pipe, and made a horizontal section,
to go through the side wall. Pulled off the sheet-rock between 2
studs, as well as the exterior wall, and made a 16X16 hole in the
wall. Put a floor in it (wood, I think) and used sheet metal to re-cover
the hole, after the pipe went through. Filled up the cavity with
vermiculite, since it is light and fireproof.
Like most old wood-burning stoves, this one had a lever on it, to
direct the exhaust around the oven, before going up the pipe.
Yes, I did cook on it. (And, in the oven.)
steve
10 ER, stripped down.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
Basic 10ER, Parts machine. Will be a semi-dedicated drill-press machine.
10 ER, a "survivor" of the trailer fire, in the back yard, needing restoration. Has a Mk5 headrest. Finally, stripped down.
Numerous parts, for Model 10 stuff. Except for lower saw guard, A and B adapters, I've got it.
Looking for one more, or some 9 inch extension table raisers.
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Thinking about getting this for heat
skou wrote:Dennis, when I lived in Oklahoma, and had ER#1, I had something similar.
Except, it was a real kitchen wood-burning range.
Old fashioned, all Cast Iron, and did a GREAT job of heating
the garage.
I used dual-wall stove pipe, and made a horizontal section,
to go through the side wall. Pulled off the sheet-rock between 2
studs, as well as the exterior wall, and made a 16X16 hole in the
wall. Put a floor in it (wood, I think) and used sheet metal to re-cover
the hole, after the pipe went through. Filled up the cavity with
vermiculite, since it is light and fireproof.
Like most old wood-burning stoves, this one had a lever on it, to
direct the exhaust around the oven, before going up the pipe.
Yes, I did cook on it. (And, in the oven.)
steve
You be the man, good morning!!!! Skou you make my nights, or should I say my WI early AMs!! We got to met up in person and JPG too!!!
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Thinking about getting this for heat
I have the Big Buddy that I used in my outside very drafty 12x16 shop with little insulation. On a day with little or no wind, it could raise the temperature about 20-25 degrees in an hour or so on high (both burners), then I would turn it to low or medium (one burner). I imagine it would do that if not better in a decently sealed garage even if no insulation. If you're going to use a propane tank, be sure to get the hose and regulator: https://smile.amazon.com/gp/product/B00 ... UTF8&psc=1. You'll probably also want the 6V adapter so you don't have to use batteries: https://smile.amazon.com/gp/product/B00 ... UTF8&psc=1.
---
Roy
How much time did you get out of a 20lb/5gal LP tank?
---
Roy
How much time did you get out of a 20lb/5gal LP tank?
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
-
ERLover
- Platinum Member
- Posts: 3914
- Joined: Mon Aug 31, 2015 10:19 pm
- Location: Greenie and Goldie Country not to metion the WI Badgers!
Re: Thinking about getting this for heat
@ Roy, I knew it!!! Moore, OK, 2013 Tornado, level 5+, it just took a bit of time to catch it, and put it together. Why was Moore, OK in my mind? That was it. It has to be more then just scary living in the "alley" 
KNOWLEDGE AND EXPERIENCE EQUALS WISDOM. Albert Einstein
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
The Greatness officially starts
Greenie, Grayling, SS stand alone BS and BS SPT, jointer and belt sander, 3 Ers with Speed Changers. I think those 3 cover my ER needs, and space for them.
- BuckeyeDennis
- Platinum Member
- Posts: 3812
- Joined: Tue Jul 24, 2012 10:03 pm
- Location: Central Ohio
Re: Thinking about getting this for heat
My family never had one when I was a boy, but there were still a few around. I especially remember a back room at the John Deere dealer, with a big old pot-bellied stove in the middle. On a cold winter day, the radiant heat from that bad boy would warm you up in nothing flat.skou wrote:Dennis, when I lived in Oklahoma, and had ER#1, I had something similar.
Except, it was a real kitchen wood-burning range.
Old fashioned, all Cast Iron, and did a GREAT job of heating
the garage.
I used dual-wall stove pipe, and made a horizontal section,
to go through the side wall. Pulled off the sheet-rock between 2
studs, as well as the exterior wall, and made a 16X16 hole in the
wall. Put a floor in it (wood, I think) and used sheet metal to re-cover
the hole, after the pipe went through. Filled up the cavity with
vermiculite, since it is light and fireproof.
Like most old wood-burning stoves, this one had a lever on it, to
direct the exhaust around the oven, before going up the pipe.
Yes, I did cook on it. (And, in the oven.)
steve
I've wanted a wood stove ever since. When we had our house built, I had an extra flue installed in the chimney chase, so that we could install a wood stove in a corner of the basement. Which corner is now in my workshop. But I can't afford to sacrifice the space at this point. Maybe in a few years I'll annex the kid's playroom, and finally put one in. The walkout door is right next to the chimney chase, so firewood access is just about ideal.
Re: Thinking about getting this for heat
I don't use it a lot, not sure I've been through a whole 5 gal tank. I started on a nearly empty tank that lasted the first season, have been on the second (full) tank for a few years. I saw one review estimate that a pound of fuel lasts about an hour on high, 2 hours on medium, 4 hours on low; I think that might be a high estimate or maybe they were using the little one lb canisters and they burn at a different rate or maybe don't have a full pound.ERLover wrote:How much time did you get out of a 20lb/5gal LP tank?
Yep, we've had two F/EF-5 tornadoes come through Moore since I've lived here, 1999 and 2013, plus a very strong EF-4 in 2003. The 99 and 03 twisters were within a few blocks of me; looked like some 50's/60's nuclear apocalypse movie where they went through. I remember seeing what had been some sort of full size pickup or SUV, couldn't tell for sure as it was crumpled into a ball. Semi rear axles, nothing attached, moved hundreds of yards. I have a large concrete cellar that I go hide in when they're headed my way.
Roy
Mark V/510, Mark V/500 with parts for 510 upgrade, bandsaw, jointer, belt sander, DC3300 w/1 micron bag
Sawstop 3HP 36" PCS w/router table insert
Home designed and built CNC router, another CNC router
desktop size, Avid 5x10 Pro CNC w/ATC, CNCed G0704 milling machine
Laser engraver
Way too much other stuff and not enough space
Mark V/510, Mark V/500 with parts for 510 upgrade, bandsaw, jointer, belt sander, DC3300 w/1 micron bag
Sawstop 3HP 36" PCS w/router table insert
Home designed and built CNC router, another CNC router
Laser engraver
Way too much other stuff and not enough space