Page 2 of 4
Re: Newb diving in
Posted: Sun May 07, 2017 8:15 pm
by jsburger
Ek1050 wrote:Ed I'm still confused on how to get the stem to fit in that tailstock hole.
It's 1 inch wide. Am I missing a fitting or a part somewhere?
It sounds like you are missing the #2 Morse taper insert for the hole in the tail stock. Look at the tail stock in the picture. It should look like that. The tail stock arbor Ed mentioned will fit in the tail stock.
The Morse taper insert is part of the tail stock as sold so if you are missing it you will probably have to contact one of the 10ER eBay guys directly since that part almost never shows up om eBay. I don't have an extra one but I think I can put you in contact with someone who might.
Re: Newb diving in
Posted: Sun May 07, 2017 11:34 pm
by reible
I have several of these but they are in use so I can't help you with one but perhaps someone else has an extra???
I'd look through your "stuff" for this:
- 20170507_205906_resized.jpg (234.65 KiB) Viewed 29069 times
Ed
Re: Newb diving in
Posted: Mon May 08, 2017 1:57 am
by rpd
And in the name of completeness, here is a side view of the drill chuck on the arbor mounted in the tailstock.
- arboranddrillchuck.JPG (270.23 KiB) Viewed 29063 times
Re: Newb diving in
Posted: Mon May 08, 2017 4:48 pm
by g_robinson
Does anyone know what "acoutrimonts" means? HAHA. you don't hear such large words being used here that often.
Re: Newb diving in
Posted: Mon May 08, 2017 7:22 pm
by reible
g_robinson wrote:Does anyone know what "acoutrimonts" means? HAHA. you don't hear such large words being used here that often.
Are you trying to spell "accoutrements"?
Ed
Re: Newb diving in
Posted: Mon May 08, 2017 7:41 pm
by jsburger
g_robinson wrote:Does anyone know what "acoutrimonts" means? HAHA. you don't hear such large words being used here that often.
I guess you would if you looked it up. BTW, it is 'accoutrements'.
Re: Newb diving in
Posted: Mon May 08, 2017 9:00 pm
by JPG
Antidisestablishmentarianism
Re: Newb diving in
Posted: Tue May 09, 2017 11:01 am
by jsburger
JPG wrote:Antidisestablishmentarianism
One of my father's favorite words.
Re: Newb diving in
Posted: Wed May 10, 2017 2:12 am
by rpd
Ek1050 wrote:Ed I'm still confused on how to get the stem to fit in that tailstock hole.
It's 1 inch wide. Am I missing a fitting or a part somewhere?
There is a floating center and nut on EBay, comes with a drive spur and a live center.
http://www.ebay.com/itm/Shopsmith-10ER- ... Sw~y9ZBQX6
Re: Newb diving in
Posted: Wed May 10, 2017 8:00 pm
by JPG
rpd wrote:Ek1050 wrote:Ed I'm still confused on how to get the stem to fit in that tailstock hole.
It's 1 inch wide. Am I missing a fitting or a part somewhere?
There is a floating center and nut on EBay, comes with a drive spur and a live center.
http://www.ebay.com/itm/Shopsmith-10ER- ... Sw~y9ZBQX6
A bit 'pricey'. They are not that scarce. The live center is brand ?. The spur center looks correct vintage.