Page 2 of 3
Re: Need help on how get started!!!!
Posted: Fri Nov 15, 2019 1:53 am
by Vetwoodrestore
I was thinking the of doing same thing saves $68
What about the ties for the wheels what are best ones to get? Any tricks aside from placeing them in warm water then install from what I know.
Re: Need help on how get started!!!!
Posted: Fri Nov 15, 2019 11:42 am
by P89DC
I bought the blue tyres from bandsawtirewerehouse on ebay. I followed their instructions and have no issues. They are working very well for the last six months.
Yes to using your old cover and adding a viewing port, I've done it to two now. Don't forget the dust port upgrade too.
There a nylon bolt by the guide under the cover too, I added it to both my bs.
I switched my bearing out too and dumped the stepped bolts for the guides and went with 7mm bolts instead.
Re: Need help on how get started!!!!
Posted: Sat Nov 16, 2019 11:23 pm
by Vetwoodrestore
Can I see what nylon bolt you are referring to?
I like to do same changed you did you your bs, where will I find these bolts an such that you changed out
Re: Need help on how get started!!!!
Posted: Sat Nov 16, 2019 11:53 pm
by reible
This is a rather large thread I did on the old cast iron top bandsaw I own. Some of the information relates to shopsmith bandsaws of any age.
https://www.shopsmith.com/ss_forum/main ... t8361.html
Ed
Re: Need help on how get started!!!!
Posted: Sun Nov 17, 2019 12:44 pm
by P89DC
Ed's thread has all the info but it's diluted by our tendency to wander. I used the info from Ed's thread and a few others. Then I overhauled/resto'ed two bandsaws. Here's my single post, very simple:
https://www.shopsmith.com/ss_forum/main ... 23070.html
Re: Need help on how get started!!!!
Posted: Sun Nov 17, 2019 5:04 pm
by Vetwoodrestore
thank you! i will review
next is to see if i have to trash my jigsaw due to no access to parts anymore
Re: Need help on how get started!!!!
Posted: Sun Nov 17, 2019 5:06 pm
by Vetwoodrestore
great more info love it.
what and or how do you fix jigsaw due to parts no longer available ???
Re: Need help on how get started!!!!
Posted: Sun Nov 17, 2019 5:14 pm
by P89DC
What's broke? If the connecting rod is broke, fabricate a new one. Make a gasket for the crank case cover. Fabricate a table insert. Soak the air pump seals and replace the hose. Scavage a spring for the upper housing. What else is there?
Re: Need help on how get started!!!!
Posted: Thu Nov 21, 2019 11:18 am
by Vetwoodrestore
What ever the plastic connecting thing was inside it. I cant even tell what it was all I see is parts of plastic. Gasket seems good I will put oil on it an see how it does. So in that housing its ment to be filled with oil? I have read few using a different oil then what is recommended?
Spring seems fine, will the scroll saw upgrade they sell for the blade change an block upgrade work?
On top of the spring there is a felt pad inside is there anything I should do or not do with that?
Re: Need help on how get started!!!!
Posted: Thu Nov 21, 2019 12:06 pm
by rpd
Vetwoodrestore wrote:What ever the plastic connecting thing was inside it. I cant even tell what it was all I see is parts of plastic. Gasket seems good I will put oil on it an see how it does. So in that housing its meant to be filled with oil? I have read few using a different oil then what is recommended?
Spring seems fine, will the scroll saw upgrade they sell for the blade change an block upgrade work?
On top of the spring there is a felt pad inside is there anything I should do or not do with that?
The plastic think is called a yoke. You can make a replacement that is better/stronger than the original quite easily. This short video will show you how.
[youtube]
https://www.youtube.com/watch?v=Rb17icIjzeA[/youtube].
I don't think the scrollsaw part would work.
You can download the manual for the jigsaw from this link.
http://vintagemachinery.org/pubs/detail.aspx?id=10571