Posted: Tue Sep 07, 2010 7:05 pm
So, Is it correct to conclude that Greenies and Early Goldies(Gilmer) do NOT have the 'hooked' key and bored shaft? I am not clear what was done in 1994(gilmer to poly-v?).
Shopsmith Forums
A woodworking forum for woodworking hobbyist and woodworking projects related and unrelated to the Shopsmith MARK V
https://forum.shopsmith.com/
So maybe that's why there are no details?
Page 2 of 2
Posted: Tue Sep 07, 2010 7:19 pm
===========================
Posted: Tue Sep 07, 2010 7:49 pm
judaspre1982 wrote:I would say it is safe to say that at least the Greenie versions did not have the hooked key and recessed key way. Not sure when the upgrade was done to those parts.
The receipt I posted was when the original owner sent the headstock out in 1994 to replace the idler shaft and its related parts( this was still a Gilmer Drive system at this time ). I did the upgrade( Poly V ) to this headstock in early 2008. I purchased the machine in 1994 after the original owner passed away. The machine sat for 14 years in an unheated masonry building until I was able to get my first shop to use it in (2007)
Dave
Makes sense now! In 1994 there was no reason to stock Gilmer version idler SHAFTS/KEYS.
Guess we will have to wait for Eastern Gray to tear down his 3/4hp Gilmer Goldie when going Power Pro - Unless Bill wants to jump in with the 'straight' scoop!:rolleyes:
Posted: Wed Sep 08, 2010 12:03 am
My shaft has a cross-wise key seat ground into it that I made the bent key hook into. Then when I slid the idler pulley on, it bottoms out at the retaining ring next to the bearing. Then I slid the clip over the shaft until it snaps into the groove where you had shown (nested down between the fins of the idler pulley. Then the control pulley indexes on the key, slides down, and shazam - done. Great pictures. If I did not get so greasy, I'd have taken my camera and made some photos. I always forget that part.
BTW - This is a great forum - thanks for being here.
BTW - This is a great forum - thanks for being here.
Posted: Wed Sep 08, 2010 8:48 am
My greenie has the hooked key and recessed key way. My father-in-law was the original owner, and I'm 99% sure he did not replace the idler shaft.judaspre1982 wrote:I would say it is safe to say that at least the Greenie versions did not have the hooked key and recessed key way. Not sure when the upgrade was done to those parts.
The receipt I posted was when the original owner sent the headstock out in 1994 to replace the idler shaft and its related parts( this was still a Gilmer Drive system at this time ). I did the upgrade( Poly V ) to this headstock in early 2008. I purchased the machine in 1994 after the original owner passed away. The machine sat for 14 years in an unheated masonry building until I was able to get my first shop to use it in (2007).
Dave
Sincerely,
Ron309753
Posted: Wed Sep 08, 2010 11:43 am
==============================
Posted: Wed Sep 08, 2010 3:56 pm
IIRC 309753 was September '55
Sincerely,
Ron309753
Sincerely,
Ron309753
Posted: Thu Sep 09, 2010 12:03 am
My S/N is 308543 - somewhere in 1955 I surmised.
Posted: Mon Sep 13, 2010 2:00 pm
I powered it up this AM, and no go 
- had to hand adjust down to slow speed - and VOILA - it's alive - and running smoothly.
Thanks for the helps here - appreciate it.
- had to hand adjust down to slow speed - and VOILA - it's alive - and running smoothly.Thanks for the helps here - appreciate it.