Clearer Setup Diagrams/Instructions?
Moderator: admin
-
- Gold Member
- Posts: 50
- Joined: Thu Jan 29, 2015 9:09 pm
- Location: Scottsville, Va
- Contact:
Re: Clearer Setup Diagrams/Instructions?
It appears this is being addressed so I suspect we'll hear something soon.
Steve
Steve
Steve
2015 ShopSmith Mark 7
Jointer
www.astral-imaging.com
2015 ShopSmith Mark 7
Jointer
www.astral-imaging.com
Re: RE: Re: Clearer Setup Diagrams/Instructions?
Correct. Here is a pic of the clamp we need. Also, no fence. Fence or pins, still need the clamp.sreilly24590 wrote:Actually what that shows is using the pins and the guard instead of the fence in place.
Steve
http://www.shopsmith.com/ownersite/cata ... use1_l.jpg
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
-
- Gold Member
- Posts: 50
- Joined: Thu Jan 29, 2015 9:09 pm
- Location: Scottsville, Va
- Contact:
Re: Clearer Setup Diagrams/Instructions?
Ya, I was going to post that as well.
Steve
Steve
Steve
2015 ShopSmith Mark 7
Jointer
www.astral-imaging.com
2015 ShopSmith Mark 7
Jointer
www.astral-imaging.com
Re: Clearer Setup Diagrams/Instructions?
I sure never saw that bar or clamp but then I never did order the speed increaser parts. I have the shield and the bar with t-nut and then the 520 version of the fence kit but they did not come with the extra part in question.
If the "bar" comes with the clamp then I'd have to guess that it might be more expensive then I want to go to add it. I can make a bar and just use a C-clamp, well unless it is really a good deal price wise.
Is there anyone reading this that has the speed increaser with this part that could take a picture of it and perhaps give us some dimensions?
Ed
If the "bar" comes with the clamp then I'd have to guess that it might be more expensive then I want to go to add it. I can make a bar and just use a C-clamp, well unless it is really a good deal price wise.
Is there anyone reading this that has the speed increaser with this part that could take a picture of it and perhaps give us some dimensions?
Ed
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
- JPG
- Platinum Member
- Posts: 35457
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
Re: Clearer Setup Diagrams/Instructions?
10ER rear fence clamp to the rescue yet again!



╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
- dusty
- Platinum Member
- Posts: 21481
- Joined: Wed Nov 22, 2006 6:52 am
- Location: Tucson (Wildcat Country), Arizona
Re: Clearer Setup Diagrams/Instructions?
The online catalog would leave one to believe that the hardware required to mount the Shaper/Router Guard is part of the kit.reible wrote:I sure never saw that bar or clamp but then I never did order the speed increaser parts. I have the shield and the bar with t-nut and then the 520 version of the fence kit but they did not come with the extra part in question.
If the "bar" comes with the clamp then I'd have to guess that it might be more expensive then I want to go to add it. I can make a bar and just use a C-clamp, well unless it is really a good deal price wise.
Is there anyone reading this that has the speed increaser with this part that could take a picture of it and perhaps give us some dimensions?
Ed
I have the Shield and the threaded post upon which it mounts but they came to me as part of the Free Standing Router Table 555414 (back in 1990). No clamp. I believe the clamp came into being as an adaptation for over/under routing on the Mark V Main Table.
"Making Sawdust Safely"
Dusty
Sent from my Dell XPS using Firefox.
Dusty
Sent from my Dell XPS using Firefox.
Re: Clearer Setup Diagrams/Instructions?
I think what we are finding is that the only place that bit of hardware exists is with the speed increaser, see it here:
http://www.shopsmith.com/ownersite/cata ... reaser.htm
You can see it in the picture but it is not called out for in the description.
I ordered the router guard shown as "A" here:
http://www.shopsmith.com/ownersite/cata ... sories.htm
And it did not come with or even hinted at the extra part shown in the previous link.
If it had not been for a discussion about the part I would have not even been aware of its existence. It makes since that the part exists but it is unclear as to how one gets it without having to order the speed increaser.
Ed
http://www.shopsmith.com/ownersite/cata ... reaser.htm
You can see it in the picture but it is not called out for in the description.
I ordered the router guard shown as "A" here:
http://www.shopsmith.com/ownersite/cata ... sories.htm
And it did not come with or even hinted at the extra part shown in the previous link.
If it had not been for a discussion about the part I would have not even been aware of its existence. It makes since that the part exists but it is unclear as to how one gets it without having to order the speed increaser.
Ed
dusty wrote:
The online catalog would leave one to believe that the hardware required to mount the Shaper/Router Guard is part of the kit.
I have the Shield and the threaded post upon which it mounts but they came to me as part of the Free Standing Router Table 555414 (back in 1990). No clamp. I believe the clamp came into being as an adaptation for over/under routing on the Mark V Main Table.
{Knight of the Shopsmith} [Hero's don't wear capes, they wear dog tags]
Re: Clearer Setup Diagrams/Instructions?
We overlooked the clamp/hardware when creating the MARK 7 starter package and will be correcting that omission. We are also in the process of identifying which customers were affected by this problem.
For those who had previously owned the fence and then purchased the Double-Tilt upgrade, we will create an item number to allow the clamp/hardware to be ordered.
For those who had previously owned the fence and then purchased the Double-Tilt upgrade, we will create an item number to allow the clamp/hardware to be ordered.
Shopsmith I.T.
Re: RE: Re: Clearer Setup Diagrams/Instructions?
Yay. Nice work Admin!admin wrote:We overlooked the clamp/hardware when creating the MARK 7 starter package and will be correcting that omission. We are also in the process of identifying which customers were affected by this problem.
For those who had previously owned the fence and then purchased the Double-Tilt upgrade, we will create an item number to allow the clamp/hardware to be ordered.
PowerPro Mark 7, 11" Bandsaw, 4" Jointer, 12" Professional Planer, DC3300 Dust Collector, DW745, DW718 w/ DW723 and a DW788 w/ DW7880.
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Success is not final, failure is not fatal: it is the courage to continue that counts. -Winston Churchill
Re: RE: Re: Clearer Setup Diagrams/Instructions?
I can't take credit for this one. They were aware and had already solved it, before I got the question asked.Skizzity wrote:Yay. Nice work Admin!admin wrote:We overlooked the clamp/hardware when creating the MARK 7 starter package and will be correcting that omission. We are also in the process of identifying which customers were affected by this problem.
For those who had previously owned the fence and then purchased the Double-Tilt upgrade, we will create an item number to allow the clamp/hardware to be ordered.
Shopsmith I.T.