Page 3 of 4
Re: Newb diving in
Posted: Wed May 10, 2017 8:12 pm
by jsburger
JPG wrote:rpd wrote:Ek1050 wrote:Ed I'm still confused on how to get the stem to fit in that tailstock hole.
It's 1 inch wide. Am I missing a fitting or a part somewhere?
There is a floating center and nut on EBay, comes with a drive spur and a live center.
http://www.ebay.com/itm/Shopsmith-10ER- ... Sw~y9ZBQX6
A bit 'pricey'. They are not that scarce. The live center is brand ?. The spur center looks correct vintage.
I certainly agree. The same seller has the tail stock casting without the eccentric on eBay for $30. Go figure. I would not pay more than $15 or $20 for the complete tail stock.
Re: Newb diving in
Posted: Thu May 11, 2017 12:45 am
by Ek1050
Realized I needed to derustify and knock the center out of the tailstock piece in order to get the tapered chuck in there.
Re: Newb diving in
Posted: Thu May 11, 2017 12:48 am
by Ek1050
Thanks again, gentlemen. The photos were helpful. Im using th original non-live center and that center holder piece of the tailstock attachment (to be technical) wasn't budging. I'm in business now!
Re: Morse taper insert for tailstock 10er
Posted: Sun Jul 14, 2019 8:58 pm
by Bartojj
- 8E4F67DB-14B9-481F-A8E9-274DAA829C9B.jpeg (884.15 KiB) Viewed 22776 times
I’m in the process of revitalizing my father’s old 10er.
I remember him turning spindles on it as a kid.
But when reassembling the machine, it is missing the tailstock insert.
From reading these forums I understand that it is a Morse 2 taper insert.
See the attached pictures which I copied from this morning were very helpful.
Does anyone know where I can buy a replacement tailstock insert for a 10er?
Re: Morse taper insert for tailstock 10er
Posted: Sun Jul 14, 2019 9:18 pm
by rpd
Bartojj wrote:8E4F67DB-14B9-481F-A8E9-274DAA829C9B.jpegI’m in the process of revitalizing my father’s old 10er.
I remember him turning spindles on it as a kid.
But when reassembling the machine, it is missing the tailstock insert.
From reading these forums I understand that it is a Morse 2 taper insert.
See the attached pictures which I copied from this morning were very helpful.
Does anyone know where I can buy a replacement tailstock insert for a 10er?
try MKCtools,
http://www.mkctools.com/10erparts.htm
or HogWinslow.
https://sites.google.com/site/hogwinslowwoodworking/
They both have parts not listed on their web pages so may be able to help you.
Re: Newb diving in
Posted: Sun Jul 14, 2019 9:24 pm
by rpd
Oh, and MKCtools has the specs so you can make one or have one made. I knew I had seen it somewhere, just took some time to find it.
http://www.mkctools.com/10erfloatingcentersub.htm
Re: Morse taper insert for tailstock 10er
Posted: Mon Jul 15, 2019 9:27 am
by Bartojj
rpd wrote:Bartojj wrote:8E4F67DB-14B9-481F-A8E9-274DAA829C9B.jpegI’m in the process of revitalizing my father’s old 10er.
I remember him turning spindles on it as a kid.
But when reassembling the machine, it is missing the tailstock insert.
From reading these forums I understand that it is a Morse 2 taper insert.
See the attached pictures which I copied from this morning were very helpful.
Does anyone know where I can buy a replacement tailstock insert for a 10er?
try MKCtools,
http://www.mkctools.com/10erparts.htm
or HogWinslow.
https://sites.google.com/site/hogwinslowwoodworking/
They both have parts not listed on their web pages so may be able to help you.
Very helpful. Thank you!
Re: Newb diving in
Posted: Tue Jul 16, 2019 1:17 pm
by JPG
More simply, just order a new one from The mother ship. The current one fits.
Re: Newb diving in
Posted: Tue Jul 16, 2019 11:04 pm
by rpd
JPG wrote:More simply, just order a new one from The mother ship. The current one fits.
But the Mother Ship doesn't stock 10ER specific parts.
Re: Newb diving in
Posted: Tue Jul 16, 2019 11:29 pm
by JPG
rpd wrote:JPG wrote:More simply, just order a new one from The mother ship. The current one fits.
But the Mother Ship doesn't stock 10ER specific parts.
BUT the tailstock has not changed since then.
So that pix misled me. He needs that thing circled in the pix, not the tailstock center that inserts into it.
I think a simple way to get one is to find one on a 10
ER tailstock from E-Bay.