Guys I am new to your forum. I do need your help, I have a problem with my Mark V that is driving me crazy. A little history I bought this machine about 4 years ago and have been slowly upgrading the tables to 510.
The crazy problem is today while trying to make a dado crossgrain the quill or something is moving slightly. I tightened everything down and then rechecked. I am trying cut a 1/2 inch deep 3/4 wide dado and the blade moves away from the power head. Any suggestions would really be appreciated.
creeping
Moderator: admin
I assume you are seeing this movement even with the spindle lock engaged. The first thing I'd check is the retaining ring behind the spindle knob. Remove the spindle knob (part 65 on this diagram http://www.shopsmith.com/service/headst ... iagram.htm) and check to make sure that the retaining ring (64 on that diagram) is installed properly in its groove and that is is snug up against the bearing behind it. If it isn't, you can get some in and out movement of the spindle.
Good luck,
Al
Good luck,
Al
Gale's Law: The bigger the woodworking project, the less the mistakes show in any photo taken far enough away to show the entire project!
Get a Sharpie or other marker that will mark a fine line. Mark everything: Everything - the headstock as it sits on the waytubes, the quill, the table. You will quickly discover where the movement is and can go from there.
Creep can occur because the headstock isn't clamped sufficiently or the table or something else.
Should be easy to track down.
Creep can occur because the headstock isn't clamped sufficiently or the table or something else.
Should be easy to track down.
First off. Welcome to the SS forum Jack1943, just in case ya didn't get one last year when ya joined. 
Are ya sure the headstock, carriage and spindle locks are engaged?
Are ya sure the headstock, carriage and spindle locks are engaged?
SS 500(09/1980), DC3300, jointer, bandsaw, belt sander, Strip Sander, drum sanders,molder, dado, biscuit joiner, universal lathe tool rest, Oneway talon chuck, router bits & chucks and a De Walt 735 planer,a #5,#6, block planes. ALL in a 100 square foot shop.
.
.
Bob
.
.
Bob
-
JPG
- Platinum Member
- Posts: 35600
- Joined: Wed Dec 10, 2008 7:42 pm
- Location: Lexington, Ky (TAMECAT territory)
If nothing else is 'moving', watch for blade warp due to over heating.beeg wrote:First off. Welcome to the SS forum Jack1943, just in case ya didn't get one last year when ya joined.
Are ya sure the headstock, carriage and spindle locks are engaged?
You do have all 5 locks secured!
╔═══╗
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange
╟JPG ╢
╚═══╝
Goldie(Bought New SN 377425)/4" jointer/6" beltsander/12" planer/stripsander/bandsaw/powerstation /Scroll saw/Jig saw /Craftsman 10" ras/Craftsman 6" thicknessplaner/ Dayton10"tablesaw(restoredfromneighborstrashpile)/ Mark VII restoration in 'progress'/ 10E[/size](SN E3779) restoration in progress, a 510 on the back burner and a growing pile of items to be eventually returned to useful life. - aka Red Grange